• State Verified Answer
  • Replies 25 replies
  • Answers 1 answer
  • Subscribers 68 subscribers
  • Views 7247 views
  • Users 0 members are here
Attachments (0)
Nordic Case Info
  • Case ID: 228706
Options
This post is older than 2 years and might not be relevant anymore
More Info: Consider searching for newer posts

AT24C512 + BMI160 + NRF52

Sunil vignesh

Hi,

I am using nRF52832 soc to develop my project. with nRF5_SDK_15.3 . SES file

I need to connect both BMI160 accelerometer sensor and AT24C512 EEPROM ic in TWI.

how to use TWI with this. guide me to use both at a time.

BMI160 separately i can read the data.

but i can't read while connect to AT24C512

Parents
  • 0
    Sunil vignesh said:
    my concern is to make multiple slaves for a one master is getting complexes

    I suggest that you go back to basics:

    1. Make sure that you understand the basics of I2C.
       
    2. Start with the TWI Scanner example.
      This will verify that your hardware connections are correct & working, and confirm that you have the correct Slave Addresses.
       
    3. Spend time studying this example, to understand how it works.
      Practice using the debugger to step through your code, examine variables, etc
      Practice using an oscilloscope or logic analyser to view what's happening on the wires.
       
    4. Save the Project - so that you can come back to it for reference later.
       
    5. Use the TWI Master example with just one of your slaves.
      Get that Slave working on its own.
      Again, practice using the debugger, scope, etc.
       
    6. Save the Project - you will need it later.
       
    7. Start again with the unmodified TWI Master example with the other of your slaves.
      Get that Slave working on its own.
       
    8. Save the Project - so that you can come back to it for reference later
       
    9. Now merge your two TWI Master projects together

    I suggest that you adopt an approach like this for all your projects:

    • Start with working examples;
    • Know your tools;
    • Take small steps at a time;
    • Keep "snapshots" of your work so that you can go back if things go wrong.
  • 0 in reply to awneil

    HI,

    I have combined the code in a same TWI0 as

    void E_twi_init (void)
{
    ret_code_t err_code;
const nrf_drv_twi_config_t twi_e_config = {
       .scl                = ARDUINO_SCL_PIN,
       .sda                = ARDUINO_SDA_PIN,
       .frequency          = NRF_DRV_TWI_FREQ_100K,
       .interrupt_priority = APP_IRQ_PRIORITY_HIGH,
       .clear_bus_init     = false
    };

    err_code = nrf_drv_twi_init(&m_twi, &twi_e_config, NULL, NULL);
    
    APP_ERROR_CHECK(err_code);
    if (NRF_SUCCESS == err_code)
	{
		nrf_drv_twi_enable(&m_twi);
		NRF_LOG_INFO("EEPROM TWI init success...");	
	}
}

    / <e> TWI0_ENABLED - Enable TWI0 instance
//==========================================================
#ifndef TWI0_ENABLED
#define TWI0_ENABLED 1
#endif
// <q> TWI0_USE_EASY_DMA  - Use EasyDMA (if present)
 

#ifndef TWI0_USE_EASY_DMA
#define TWI0_USE_EASY_DMA 1
#endif

// </e>

// <e> TWI1_ENABLED - Enable TWI1 instance
//==========================================================
#ifndef TWI1_ENABLED
#define TWI1_ENABLED 0
#endif
// <q> TWI1_USE_EASY_DMA  - Use EasyDMA (if present)

    can you check my code

    it is reliable ?!  (i.e - It work for long real time process)

    #include <stdio.h>
#include "boards.h"
#include "app_util_platform.h"
#include "app_error.h"
#include "nrf_drv_twi.h"
#include "nrf_delay.h"


#include "nrf_log.h"
#include "nrf_log_ctrl.h"
#include "nrf_log_default_backends.h"

#include "bmi160.h"

/* TWI instance ID. */
#define TWI_INSTANCE_ID     0
#define TWI1_INSTANCE_ID     1
#define I2C_24C128_SLAVE_ADDR        (0x50)
#define G_TO_LSB (16384.0f)

#define DPS_TO_LSB (131.072f)

/* Indicates if operation on TWI has ended. */
static volatile bool m_xfer_done = false;

/* TWI instance. */
static const nrf_drv_twi_t m_twi = NRF_DRV_TWI_INSTANCE(TWI_INSTANCE_ID);
//static const nrf_drv_twi_t m_twi_e = NRF_DRV_TWI_INSTANCE(TWI1_INSTANCE_ID);

void eep_WriteByte(uint16_t eep_address, unsigned char val);
unsigned char eep_readByte(uint16_t eep_address);
ret_code_t err_codecpy;

struct bmi160_dev sensor;
struct bmi160_sensor_data accel;
struct bmi160_sensor_data gyro;
struct bmi160_int_settg int_config;

int8_t rslt = BMI160_OK;



void B_twi_init (void)
{
    ret_code_t err_code;

    const nrf_drv_twi_config_t twi_config = {
       .scl                = ARDUINO_SCL_PIN,
       .sda                = ARDUINO_SDA_PIN,
       .frequency          = NRF_DRV_TWI_FREQ_100K,
       .interrupt_priority = APP_IRQ_PRIORITY_HIGH,
       .clear_bus_init     = false
    };

    err_code = nrf_drv_twi_init(&m_twi, &twi_config, NULL, NULL);
    NRF_LOG_INFO("err_code :%d", err_code);
    APP_ERROR_CHECK(err_code);
    if (NRF_SUCCESS == err_code)
	{
		nrf_drv_twi_enable(&m_twi);
		NRF_LOG_INFO("BMI TWI init success...");	
	}
}

void E_twi_init (void)
{
    ret_code_t err_code;
const nrf_drv_twi_config_t twi_e_config = {
       .scl                = ARDUINO_SCL_PIN,
       .sda                = ARDUINO_SDA_PIN,
       .frequency          = NRF_DRV_TWI_FREQ_100K,
       .interrupt_priority = APP_IRQ_PRIORITY_HIGH,
       .clear_bus_init     = false
    };

    err_code = nrf_drv_twi_init(&m_twi, &twi_e_config, NULL, NULL);
    
    APP_ERROR_CHECK(err_code);
    if (NRF_SUCCESS == err_code)
	{
		nrf_drv_twi_enable(&m_twi);
		NRF_LOG_INFO("EEPROM TWI init success...");	
	}
}
unsigned char eep_readByte(uint16_t eep_address)
{

    unsigned char eep_by_address[2];
    unsigned char reg=0;
    eep_by_address[1]   = eep_address;
    eep_by_address[0] = (unsigned char)(eep_address << 8);
    // setting the start address
    nrf_drv_twi_tx(&m_twi, I2C_24C128_SLAVE_ADDR, eep_by_address, 2, true);
    // read a byte
    nrf_delay_ms(5);

    nrf_drv_twi_rx(&m_twi, I2C_24C128_SLAVE_ADDR, &reg,1);

    nrf_delay_ms(5);
	return reg;
}
void eep_WriteByte(uint16_t eep_address, unsigned char val)
{

    unsigned char eep_by_address[3];
    eep_by_address[2] = val;
    eep_by_address[1] = eep_address;
    eep_by_address[0] = (unsigned char)(eep_address << 8);

    err_codecpy = nrf_drv_twi_tx(&m_twi, I2C_24C128_SLAVE_ADDR, eep_by_address, 3, false);
    nrf_delay_ms(5);
    if(err_codecpy == 0)
    {
      NRF_LOG_INFO("\r\nWritten Sucess");
    NRF_LOG_FLUSH();
    }

}



int8_t Acc_i2c_Write(uint8_t dev_id, uint8_t reg_addr, uint8_t *reg_data, uint16_t len)
{

    //  NRF_LOG_INFO("WRITE: dev_id: %x reg_addr: %x reg_data: %x len: %i\n", dev_id, reg_addr, *reg_data, len);
	int8_t rslt = 0;
	uint8_t data[len + 1];
	data[0] = reg_addr;
	for (uint16_t i = 0; i < len; i++) {
		data[i + 1] = reg_data[i];
	}
	
	rslt = nrf_drv_twi_tx(&m_twi, dev_id, data, len + 1, false);
	APP_ERROR_CHECK(rslt);
        return rslt;
  
}


int8_t Acc_i2c_Read(uint8_t dev_id, uint8_t reg_addr, uint8_t *reg_data, uint16_t len)
{
	int8_t rslt = 0;
   //     NRF_LOG_INFO("READ: dev_id: %x reg_addr: %x len: %i\n", dev_id, reg_addr, len);
	rslt = nrf_drv_twi_tx(&m_twi, dev_id, &reg_addr, 1, false);
        APP_ERROR_CHECK(rslt);

	if (rslt == 0)
	{
		rslt = nrf_drv_twi_rx(&m_twi, dev_id, reg_data, len);
	}
    //    NRF_LOG_INFO("READ: %x",*reg_data);
	return rslt;
}

void Acc_delay_ms(uint32_t period)
{ 
  nrf_delay_ms( period ) ;
}

void BMI_init (void)
{
    sensor.id = BMI160_I2C_ADDR;         //0x69
    sensor.interface = BMI160_I2C_INTF;  //0x00
    sensor.read = &Acc_i2c_Read;
    sensor.write = &Acc_i2c_Write;
    sensor.delay_ms = &Acc_delay_ms;

    rslt = bmi160_init(&sensor);
    APP_ERROR_CHECK(rslt);

    if(rslt == BMI160_OK){
    NRF_LOG_INFO("BMI160 Initialized...");
    } else {
    NRF_LOG_INFO("BMI160 not Initialized...");
    }NRF_LOG_FLUSH();

    sensor.accel_cfg.odr = BMI160_ACCEL_ODR_1600HZ;
    sensor.accel_cfg.range = BMI160_ACCEL_RANGE_2G;
    sensor.accel_cfg.bw = BMI160_ACCEL_BW_NORMAL_AVG4;
    sensor.accel_cfg.power = BMI160_ACCEL_NORMAL_MODE;

    sensor.gyro_cfg.odr = BMI160_GYRO_ODR_3200HZ;
    sensor.gyro_cfg.range = BMI160_GYRO_RANGE_2000_DPS;
    sensor.gyro_cfg.bw = BMI160_GYRO_BW_NORMAL_MODE;
    sensor.gyro_cfg.power = BMI160_GYRO_NORMAL_MODE;

    rslt = bmi160_set_sens_conf(&sensor);
    APP_ERROR_CHECK(rslt);

     if(rslt == BMI160_OK){
    NRF_LOG_INFO("sensor Configured...");
    } else {
    NRF_LOG_INFO("sensor not Configured...");
    }NRF_LOG_FLUSH();
}
/**
 * @brief Function for reading data from temperature sensor.
 */
static void read_sensor_data()
{
    m_xfer_done = false;
    unsigned char  reg1 = 0;
    bmi160_get_sensor_data((BMI160_ACCEL_SEL | BMI160_GYRO_SEL | BMI160_TIME_SEL), &accel, &gyro, &sensor);
    float accelX = ((((float)accel.x) / G_TO_LSB) * 9.80655); // in m/s^2
      float gyrX = ((((float)gyro.x) / DPS_TO_LSB) * 0.0174532925); // in rad/sec
      NRF_LOG_INFO("DataX in m/s^2   : " NRF_LOG_FLOAT_MARKER, 
      NRF_LOG_FLOAT( accelX));
      NRF_LOG_INFO("DataY in rad/sec : " NRF_LOG_FLOAT_MARKER, 
      NRF_LOG_FLOAT(gyrX));
      NRF_LOG_FLUSH();
       nrf_delay_ms(50);
       eep_WriteByte(0x00051,accelX);
        reg1=eep_readByte(0x00051);
	if(reg1!=0){
		NRF_LOG_INFO("\r\n Read value 51 : %d",reg1);
                NRF_LOG_FLUSH();
                nrf_delay_ms(5);
	}
	else if(reg1==0){
        NRF_LOG_INFO("\r\n can't Read value 51 ");
	 nrf_delay_ms(5);
	}
}

/**
 * @brief Function for main application entry.
 */
int main(void)
{ bsp_board_init(BSP_INIT_LEDS);
    APP_ERROR_CHECK(NRF_LOG_INIT(NULL));
    NRF_LOG_DEFAULT_BACKENDS_INIT();
     NRF_LOG_INFO("EEPROM get started.\n");
    NRF_LOG_FLUSH();
    Acc_delay_ms(100);


    E_twi_init();
    Acc_delay_ms(50);
    unsigned char  reg1 = 0;
    
    nrf_delay_ms(1000);
    nrf_delay_ms(5);
	   reg1=eep_readByte(0x0000);
	if(reg1!=0){
		NRF_LOG_INFO("\r\n Read value 00 : %x",reg1);
                NRF_LOG_FLUSH();
                nrf_delay_ms(5);
	}

	else if(reg1==0){
	 nrf_delay_ms(5);
	}
        nrf_delay_ms(3000);

     eep_WriteByte(0x0000,'S');
    nrf_delay_ms(5);
	   reg1=eep_readByte(0x0000);
	if(reg1!=0){
		NRF_LOG_INFO("\r\n Read value 00 : %x",reg1);
                NRF_LOG_FLUSH();
                nrf_delay_ms(5);
	}

	else if(reg1==0){
	 nrf_delay_ms(5);
	}

    NRF_LOG_INFO("BMI160 get started.\n");
    NRF_LOG_FLUSH();
    Acc_delay_ms(100);
   // nrf_drv_twi_disable(&m_twi_e);


    //B_twi_init();
    Acc_delay_ms(50);

    BMI_init();
    Acc_delay_ms(100);
    uint8_t reg_addr = BMI160_CHIP_ID_ADDR;
    uint8_t data;
    uint16_t len = 1;
    Acc_delay_ms(1000);
    rslt = bmi160_get_regs(reg_addr, &data, len, &sensor);
    NRF_LOG_INFO("Data:%x", data);
    NRF_LOG_FLUSH();
    Acc_delay_ms(3000);
    
    while (true)
    {
        nrf_delay_ms(250);
        read_sensor_data();

        NRF_LOG_FLUSH();
    }
}

/** @} */

    OUTPUT:

    <info> app: EEPROM get started.

<info> app: EEPROM TWI init success...
<info> app: 
 Read value 00 : 53
<info> app: 
Written Sucess
<info> app: 
 Read value 00 : 53
<info> app: BMI160 get started.

<info> app: BMI160 Initialized...
<info> app: sensor Configured...
<info> app: Data:D1
<info> app: DataX in m/s^2   : 2.60
<info> app: DataY in rad/sec : -0.00
<info> app: 
Written Sucess
<info> app: 
 Read value 51 : 2
<info> app: DataX in m/s^2   : 2.56
<info> app: DataY in rad/sec : -0.00
<info> app: 
Written Sucess
<info> app: 
 Read value 51 : 2

    can you tell me how to save the negative value in eeprom like (-2.05) in an address

  • 0 in reply to Sunil vignesh
    Sunil vignesh said:
    can you tell me how to save the negative value in eeprom like (-2.05)

    This is standard 'C' - nothing specifically to do with Nordic.

    The EEPROM just stores bytes - it neither knows not cares what those bytes represent.

    So you need to write functions to take your data, and write it to the EEPROM as a sequence of bytes;

    And, conversely, code to read a sequence of bytes from EEPROM and form it into your data.

    https://en.wikipedia.org/wiki/Serialization

Reply Children
No Data
Related