A terminal that can not communicate.

[zkt-1400]

I found a terminal that can not communicate with BLE.
I think that the sequence after MTU exchange is strange.
The program used is sample HRM.
The terminal used is "Xperia (TM) Z4 SO-03G".

Is there a solution?

The usage environment is as follows.

・SDK15
・Nrf 52
・Nrf 52832_xxaa
・S132_nrf52_6.0.0_softdevice.hex
・nRF5_SDK_15.0.0_a53641a \ examples \ ble_peripheral \ ble_app_hrs \ hex \ ble_app_hrs_pca10040_s132.hex

Postscript

It turned out that communication is possible with the following.

nRF5_SDK_15.0.0_a53641a\components\softdevice\common\nrf_sdh_ble.c
line157
ble_cfg.conn_cfg.params.gatt_conn_cfg.att_mtu = NRF_SDH_BLE_GATT_MAX_MTU_SIZE;
↓
ble_cfg.conn_cfg.params.gatt_conn_cfg.att_mtu = BLE_GATT_ATT_MTU_DEFAULT;

I had previously switched off the MTU exchange.
At that time, communication was not possible.

nRF5_SDK_15.0.0_a53641a\components\ble\nrf_ble_gatt\nrf_ble_gatt.c
Delete lines 150-173.

Here are the questions:

1. What is the difference between making MTU by default and turning it off?

2. If MTU is the default, will the communication speed be slower if the data size is large?

[Sigurd]

Hi,

1. What is the difference between making MTU by default and turning it off?

If you turn it off, i.e. remove the gatt module initialization, you will then not handle MTU requests from the central at all. If the MTU requests are not handled, you will get a GATT procedure timeout on the link, and the link will disconnect.

Leaving it at default, you will just respond back to the central that you support the default value of 23.

2. If MTU is the default, will the communication speed be slower if the data size is large?

You could get a higher throughput with larger MTU, but DLE(data length/NRF_SDH_BLE_GAP_DATA_LENGTH) have a greater impact on throughput than MTU.

Also, If you are using nRF-Sniffer v1, I would recommend upgrading to nRF-Sniffer v2.

[zkt-1400]

Why is it that I can not communicate even though the MTU exchange on Xperia is successful?
Why does it work for default values?

[Sigurd]

It does not work with NRF_SDH_BLE_GATT_MAX_MTU_SIZE? 

Does the device disconnect?

Could you upload a sniffer log captured with nRF-Sniffer v2?

[zkt-1400]

I will attach a new sniffer log.
Xperia Z4 SO-03G <---> sample HRM

The target terminal is Bluetooth 4.1.
The OS of the target device is Android 7.0.

Why is MTU exchange successful for devices other than 23 on Bluetooth 4.1 devices?
Will it succeed if the OS is Android 7.0?
HRM_xperia.pcapng

[Sigurd]

From the sniffer log, the phone is transmitting several packet 2 times, without waiting for response.

1) Does the issue disappear if you set NRF_SDH_BLE_GAP_DATA_LENGTH in sdk_config.h to 27 ?

2) Does the issue disappear if you set NRF_SDH_BLE_GATT_MAX_MTU_SIZE in sdk_config.h to 23 ?

[zkt-1400]

From the sniffer log, the phone is transmitting several packet 2 times, without waiting for response.

→
This phenomenon may occur with any mobile phone connected.
It can also occur when using the sample without changing it.

1) Does the issue disappear if you set NRF_SDH_BLE_GAP_DATA_LENGTH in sdk_config.h to 27 ?

→
I was able to connect.
What does this change mean?
Is the parameter different from MTU?

I will attach the log.
・HRM_DATA_LENGTH_27_iPhoneSE.pcapng
・HRM_DATA_LENGTH_27_xperia.pcapng

2) Does the issue disappear if you set NRF_SDH_BLE_GATT_MAX_MTU_SIZE in sdk_config.h to 23 ?

→
I was able to connect.
If this change is made, the MTU of all devices will be 23.
So it is not suitable for me.
When the communication partner is Bluetooth 4.2 or later, I want to extend the MTU and communicate.

I will attach the log.
・HRM_MAX_MTU_SIZE_23_iPhoneSE.pcapng
・HRM_MAX_MTU_SIZE_23_xperia.pcapng

HRM_DATA_LENGTH_27_iPhoneSE.pcapng

HRM_DATA_LENGTH_27_xperia.pcapng

HRM_MAX_MTU_SIZE_23_iPhoneSE.pcapng

HRM_MAX_MTU_SIZE_23_xperia.pcapng