httpS sample

[Marc]

Hi

I am trying to merge zephyr's http_get example (with TLS option) into the nordic mqtt_simple example (ncs 0.4.0) since I need to set up a httpS connection and not just a http connection as nordic's http_application_update shows (TLS not supported by nordic's download_client lib). I took the mqtt_simple as base since it is a simpler project than http_application_update and figured it would be easier to swap the mqtt requests with https requests.

I loaded the mqtt_simple into SES 4.16 and then tried to change the configuration using Project => Configure nRF Connect Project... and enable all symbols as given in the proj.conf of zephyr's http_get example (attached below)

# General config
CONFIG_NEWLIB_LIBC=y

# Networking config
CONFIG_NETWORKING=y
CONFIG_NET_IPV4=y
CONFIG_NET_IPV6=y
CONFIG_NET_TCP=y
CONFIG_NET_SOCKETS=y
CONFIG_NET_SOCKETS_POSIX_NAMES=y

CONFIG_DNS_RESOLVER=y
CONFIG_DNS_SERVER_IP_ADDRESSES=y
CONFIG_DNS_SERVER1="192.0.2.2"

# Network driver config
CONFIG_TEST_RANDOM_GENERATOR=y

# Network address config
CONFIG_NET_CONFIG_SETTINGS=y
CONFIG_NET_CONFIG_NEED_IPV4=y
CONFIG_NET_CONFIG_MY_IPV4_ADDR="192.0.2.1"
CONFIG_NET_CONFIG_PEER_IPV4_ADDR="192.0.2.2"
CONFIG_NET_CONFIG_MY_IPV4_GW="192.0.2.2"

# Network debug config
CONFIG_NET_LOG=y

I get the following error message after pressing "Configure" (and the whole SES project is not usable anymore..)

Loading solution mqtt_simple.emProject
Executing load commands
cmake -GNinja -DBOARD=nrf9160_pca10090ns -DBOARD_DIR=C:/work/git/ncs/zephyr/boards/arm/nrf9160_pca10090 -DZEPHYR_TOOLCHAIN_VARIANT=gnuarmemb -DGNUARMEMB_TOOLCHAIN_PATH=C:/work/gnuarmemb -BC:/work/git/ncs/nrf/samples/nrf9160/mqtt_simple/build_nrf9160_pca10090ns -HC:/work/git/ncs/nrf/samples/nrf9160/mqtt_simple -DEXTRA_KCONFIG_TARGETS=menuconfig_ses -DEXTRA_KCONFIG_TARGET_COMMAND_FOR_menuconfig_ses=C:/work/EmbeddedStudio_ARM_Nordic_v416_win_x64/arm_segger_embedded_studio_v416_win_x64_nordic/html/configure_nordic_project_menuconfig.py
-- Using application from 'C:/work/git/ncs/nrf/samples/nrf9160/mqtt_simple'
Zephyr version: 1.14.99
-- Selected BOARD nrf9160_pca10090ns
-- Found west: C:/Python37/Scripts/west.exe (found suitable version "0.5.8", minimum required is "0.5.6")
-- Cache files will be written to: C:\Users\lama5\AppData\Local/.cache/zephyr
USING OUT OF TREE BOARD
-- Loading C:/work/git/ncs/zephyr/boards/arm/nrf9160_pca10090/nrf9160_pca10090ns.dts as base
-- Overlaying C:/work/git/ncs/zephyr/dts/common/common.dts

warning: user value 0 on the int symbol DNS_RESOLVER_MAX_SERVERS (defined at subsys\net\lib\dns\Kconfig:49) ignored due to being outside the active range ([1, 0]) -- falling back on defaults

warning: default value 1 on DNS_RESOLVER_MAX_SERVERS (defined at subsys\net\lib\dns\Kconfig:49) clamped to 0 due to being outside the active range ([1, 0])
Parsing Kconfig tree in C:/work/git/ncs/nrf/samples/nrf9160/mqtt_simple/Kconfig
Loading C:/work/git/ncs/nrf/samples/nrf9160/mqtt_simple/build_nrf9160_pca10090ns/zephyr/.config as base

Error: Aborting due to non-whitelisted Kconfig warning 'warning: user value 0 on the int symbol
DNS_RESOLVER_MAX_SERVERS (defined at subsys\net\lib\dns\Kconfig:49) ignored due to being outside the
active range ([1, 0]) -- falling back on defaults'. Note: If this warning doesn't point to an actual
problem, you can add it to the whitelist at the top of
C:/work/git/ncs/zephyr/scripts/kconfig/kconfig.py.

CMake Error at C:/work/git/ncs/zephyr/cmake/kconfig.cmake:194 (message):
  command failed with return code: 1
Call Stack (most recent call first):
  C:/work/git/ncs/zephyr/cmake/app/boilerplate.cmake:500 (include)
  CMakeLists.txt:10 (include)


-- Configuring incomplete, errors occurred!
See also "C:/work/git/ncs/nrf/samples/nrf9160/mqtt_simple/build_nrf9160_pca10090ns/CMakeFiles/CMakeOutput.log".
See also "C:/work/git/ncs/nrf/samples/nrf9160/mqtt_simple/build_nrf9160_pca10090ns/CMakeFiles/CMakeError.log".
Project load failed
Reported error: solution load command failed (1)

Setting DNS_RESOLVER_MAX_SERVERS = 1 is not possible in "Configure nRF Connect Project" since it gets reset to 0 automatically. 

Also the NET_TCP symbol can not be enabled in "Configure nRF Connect Project" of the mqtt_simple sample compared to zephyr's http_get example where it is visible in "Configure nRF Connect Project". 

What am I doing wrong / what would be the right approach?

Is https even supported by the nRF9160?

BR, Marc

[jbrzozoski]

I don't have an answer to help you, but as a heads-up they just merged in a substantial re-write of the HTTP firmware updater libraries:

https://github.com/NordicPlayground/fw-nrfconnect-nrf/pull/806

https://github.com/NordicPlayground/fw-nrfconnect-nrf/pull/769

I was following along the discussion over there.  They were commenting that HTTPS is on their to-do list but not yet implemented.

[Marc]

Hi jbrzozoski

Not the answer I was hoping for, but thank you anyway! So, am I right, that the TLS layer is not yet implemented on the nRF91? If I read your documentation correctly the TLS layer would be in the modem firmware right? 

It sounds promising that they want to implement HTTPS on in the firmware updater libs. Do you have a timeline when the TLS feature will be available? I consider this quite an important topic for an IoT product.

BR,

Marc

[jbrzozoski]

TLS is implemented in the modem.  I have used it successfully underneath the MQTT library.  My comment was that they have not yet provided an example tying it together w/ HTTP(S).

[Marc]

Ok, thx! you don't have a ballpark number on when they will have an HTTPS example (weeks, months, ..)?