I am using nrf51822 chips and UART to communicate with my cellphone. I want to know if there are any ways to improve the sampling rate (reading and transmission) of measurement. I am doing the EEG stuff, so more date transitted is favorable. Thanks!
I am using nrf51822 chips and UART to communicate with my cellphone. I want to know if there are any ways to improve the sampling rate (reading and transmission) of measurement. I am doing the EEG stuff, so more date transitted is favorable. Thanks!
What "sampling rate" ?
Whether anything can be improved depends on where it's currently at - and we have no idea about that!
The nRF51822 Product Specification will tell you the capabilities of the chip.
Hi, Sampling rate relates to how many data collected in one second. More data collected in one second is preferred in my application.
The maximum sample rate of the ADC in nRF51 series is 50 kHz, but this is heavily limited by the BLE activity if a softdevice is enabled. See this post for more details.
Thanks for this useful information. I am using the softdevice and I think 2KHz is enough for my applications. I am using an APP called "Bluefruit" to receive data but found the data is far coarse than expected (less than 2KHz). What is the issue? Any other Apps to recommend?
I am using an APP called "Bluefruit"
You mean this: https://learn.adafruit.com/bluefruit-le-connect/ios-setup ?
It's always helpful to give a link, rather than expect people to just know or have to google for you.
Especially as there may be many hits; eg, https://www.bluefruit.co.uk/
What is the issue?
You really need to ask Adafruit about that; it's their app - nothing to do with Nordic!
But do note that phones often limit the available BLE throughput ...
Any other Apps to recommend
Have you looked at nRF Connect?
www.nordicsemi.com/.../nRF-Connect-for-desktop
https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Connect-for-mobile
The question is whether it is the sample rate of the ADC that is the limitation, or if it is the BLE throughput. You will not be able to send 2k packets each second, you will have to buffer up multiple samples and send these at a lower interval. Remember that the minimum connection interval in BLE is 7.5 ms, and the phone may limit this even further. With bandwidth configuration of the connection set to HIGH (6 packets per connection interval), you could send up to 800 packets each second (given that the other side of the link support this).
Hi Jorgen,
Thanks for the good point. I guess you mean 1000/7.5*6=800. Could you provide some suggestions on how to modify the code? Appreciate it!
Hi Jorgen,
Thanks for the good point. I guess you mean 1000/7.5*6=800. Could you provide some suggestions on how to modify the code? Appreciate it!
If you can post the project, I can try to help you. There are also many threads on DevZone related to the same question.
Hi Jorgen, I attached my code here. I use two channels: one for temperature and the other for ECG. Please help to take a look!
void adc_1()
{
// interrupt ADC
NRF_ADC->INTENSET = (ADC_INTENSET_END_Disabled <<
ADC_INTENSET_END_Pos); /*!< Interrupt enabled. */
// config ADC
NRF_ADC->CONFIG = (ADC_CONFIG_EXTREFSEL_None << ADC_CONFIG_EXTREFSEL_Pos) /* Bits 17..16 :
ADC external reference pin selection. */
| (ADC_CONFIG_PSEL_AnalogInput2 <<
ADC_CONFIG_PSEL_Pos) /*!< Use analog
input 0 as analog input. */
| (ADC_CONFIG_REFSEL_VBG <<
ADC_CONFIG_REFSEL_Pos) /*!<
Use internal 1.2V bandgap voltage as reference for
conversion. */
| (ADC_CONFIG_INPSEL_AnalogInputOneThirdPrescaling <<
ADC_CONFIG_INPSEL_Pos) /*!< Analog input specified by
PSEL with no prescaling used as input for the
conversion. */
| (ADC_CONFIG_RES_10bit <<
ADC_CONFIG_RES_Pos);
/*!< 10bit ADC resolution. */
// enable ADC
NRF_ADC->ENABLE =
ADC_ENABLE_ENABLE_Enabled;
/* Bit 0 : ADC enable. */
// start ADC conversion
NRF_ADC->TASKS_START = 1;
// wait for conversion to end
while (!NRF_ADC->EVENTS_END)
{}
NRF_ADC->EVENTS_END = 0;
//Save your ADC result
adc_result = NRF_ADC->RESULT;
tempvalue=-1481.96+sqrt(2196200+(1.8639-adc_result*3.3/1023)/0.00000388);
//Use the STOP task to save current. Workaround for PAN_028 rev1.1 anomaly 1.
NRF_ADC->TASKS_STOP = 1;
}
void adc_2()
{
// interrupt ADC
NRF_ADC->INTENSET = (ADC_INTENSET_END_Disabled <<
ADC_INTENSET_END_Pos); /*!< Interrupt enabled. */
// config ADC
NRF_ADC->CONFIG = (ADC_CONFIG_EXTREFSEL_None << ADC_CONFIG_EXTREFSEL_Pos) /* Bits 17..16 :
ADC external reference pin selection. */
| (ADC_CONFIG_PSEL_AnalogInput4 <<
ADC_CONFIG_PSEL_Pos) /*!< Use analog
input 0 as analog input. */
| (ADC_CONFIG_REFSEL_VBG <<
ADC_CONFIG_REFSEL_Pos) /*!<
Use internal 1.2V bandgap voltage as reference for
conversion. */
| (ADC_CONFIG_INPSEL_AnalogInputOneThirdPrescaling <<
ADC_CONFIG_INPSEL_Pos) /*!< Analog input specified by
PSEL with no prescaling used as input for the
conversion. */
| (ADC_CONFIG_RES_10bit <<
ADC_CONFIG_RES_Pos);
/*!< 10bit ADC resolution. */
// enable ADC
NRF_ADC->ENABLE =
ADC_ENABLE_ENABLE_Enabled;
/* Bit 0 : ADC enable. */
// start ADC conversion
NRF_ADC->TASKS_START = 1;
// wait for conversion to end
while (!NRF_ADC->EVENTS_END)
{}
NRF_ADC->EVENTS_END = 0;
//Save your ADC result
adc_output = NRF_ADC->RESULT;
//Use the STOP task to save current. Workaround for PAN_028 rev1.1 anomaly 1.
NRF_ADC->TASKS_STOP = 1;
}
/**@brief Application main function.
*/
int main(void)
{
uint32_t err_code;
bool erase_bonds;
uint8_t start_string[] = START_STRING;
// Initialize.
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE, false);
uart_init();
buttons_leds_init(&erase_bonds);
ble_stack_init();
gap_params_init();
services_init();
advertising_init();
conn_params_init();
printf("%s",start_string);
printf("\n\rADC HAL simple example\r\n");
printf("Current sample value:\r\n");
err_code = ble_advertising_start(BLE_ADV_MODE_FAST);
APP_ERROR_CHECK(err_code);
// Enter main loop.
while(true)
{
adc_1();
adc_2();
// trigger next ADC conversion
//nrf_adc_start();
// enter into sleep mode
__SEV();
__WFE();
__WFE();
uint8_t str[4];
sprintf((char*)str, "ADC:%d TEMP: %.2f", (int)adc_result,(float)tempvalue);//
out ADC result
ble_nus_string_send(&m_nus, str, strlen((char*)str));
nrf_delay_ms(2000);
sprintf((char*)str, "ECG-ADC: %d", (int)adc_output);
ble_nus_string_send(&m_nus, str, strlen((char*)str));
nrf_delay_ms(2000);
power_manage();
}
}
/**
* @}
*/
This is not enough to help you with throughput. The throughput depends on the BLE configuration, which you have not included in above code. To be able to help you, I would need the entire project (including main/sdk_config.h/IDE project files).