I want to interface a 16MB external flash (SPI) with nrf52832 on the development board.Suggest me how should I start with and if there is an example for external flash then let me know.
I want to interface a 16MB external flash (SPI) with nrf52832 on the development board.Suggest me how should I start with and if there is an example for external flash then let me know.
Hi
What kind of external flash device do you want to connect?
Are you planning to use a file system, or will you just access the flash using low level read/write/erase commands?
The usbd_msc example in the SDK allows you to access SD cards over the SPI interface, if you compile the example with the USE_SD_CARD define set to 1 (located on line 106 of main.c).
Unfortunately this example is designed for the nRF52840 only, since it uses the USB interface in the nRF52840 to enumerate the connected SD card as a flash drive when connected to a PC.
Best regards
Torbjørn
I want to interface MX25R1635F FLASH memory with nrf52832. And no file system but want to access its read,write and erase commands. I have seen the qspi example but got confused with it as my I have nrf52832 that does not support QSPI.
Hi Torbjorn,
I am able to read the data now.It was due to some hardware issues that I was not able to read on MISO line.But now I am facing issue in erasing the chip.what else do I need to send to erase chip/ sector/block with it's instruction command?
Hi
This should be described in the datasheet of your flash device.
If you can't find it there please share the datasheet with me, and I will have a look.
Best regards
Torbjørn
Ok sharing with you the datasheet and the code which I am using. I added delay after CS_LOW so I am able to get the chip erase done. but still the issue is that after sending chip erase function I am not abl to write it. Also sector earse is not working ,I think I am struggling with the timing issues. I will be grateful if you can help me with these issues and make my flash running propelry.MX25R1635F, Wide Range, 16Mb, v1.6.pdf
and the code as below
///**
// ******************************************************************************
// * @file ext_flash.c
// * This source file provides external flash memory related functionalities.
// *
// * @author Glide Embedded Technology <www.glidemtech.com>
// * @date 7, August, 2019
// ******************************************************************************
// */
//
///* Includes ------------------------------------------------------------------*/
///* Includes ------------------------------------------------------------------*/
#include <stdio.h>
#include <string.h>
#include <stdint.h>
//
#include "external_flash.h"
#include <hal/nrf_gpio.h>
#include <hal/nrf_spi.h>
#include "nrf_drv_spi.h"
#include "nrf_log.h"
#include "nrf_log_ctrl.h"
#include "nrf_log_default_backends.h"
#include "nrf_delay.h"
uint8_t print = 1;
#define SPI_INSTANCE 0 /**< SPI instance index. */
static const nrf_drv_spi_t spi = NRF_DRV_SPI_INSTANCE(SPI_INSTANCE);
#define WAIT_FOR_PERIPH() do { \
while (!m_finished) {} \
m_finished = false; \
} while (0)
static volatile bool m_finished = false;
static uint8_t m_buffer_tx[256];
static uint8_t m_buffer_rx[256];
//static uint8_t m_data_send[256];
static uint8_t m_data_receive[256];
#define TEST_STRING "Z" //"Nordic"
static uint8_t m_tx_buf[] = TEST_STRING; /**< TX buffer. */
static uint8_t m_rx_buf[sizeof(TEST_STRING) + 1]; /**< RX buffer. */
static const uint8_t m_length = sizeof(m_tx_buf);
static uint8_t m_buffer_tx[256];
static uint8_t m_buffer_rx[256];
//static uint8_t m_data_send[256];
static uint8_t m_data_receive[256];
static uint8_t m_data_send[256] = {[0 ... 255] = 0xbb};
uint8_t StatusReg;
uint8_t ConfigReg;
uint8_t SecurityReg;
/**
* @brief SPI user event handler.
* @param event
*/
void spi_event_handler(nrf_drv_spi_evt_t const * p_event,
void * p_context)
{
m_finished = true;
uint16_t i ;
//printf("\n\rTransfer completed.");
if (m_buffer_rx[0] != 0)
{
// printf(" Received:");
for(i=0;i<8;i++)
{
// printf("m_buffer_rx[%d] = %x ",i,m_buffer_rx[i]);
}
NRF_LOG_HEXDUMP_INFO(m_buffer_rx, strlen((const char *)m_buffer_rx));
}
// nrf_gpio_pin_set(SPI_SS_PIN);
}
void cs_low(void)
{
nrf_gpio_pin_set(SPI_SS_PIN);
}
void cs_high(void)
{
nrf_gpio_pin_clear(SPI_SS_PIN);
}
/*
* Reset setting Command
*/
/*
* Function: CMD_RSTEN
* Arguments: None.
* Description: Enable RST command
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_rsten( void )
{
// Chip select go low to start a flash command
cs_low();
// Write RSTEN command
uint8_t instruction = FLASH_CMD_RSTEN;
m_buffer_tx[0] = instruction;
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,1);
// Chip select go high to end a flash command
cs_high();
return FlashOperationSuccess;
}
/*
* Function: CMD_RST
* Arguments: fsptr, pointer of flash status structure
* Description: The RST instruction is used as a system (software) reset that
* puts the device in normal operating Ready mode.
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_rst( void )
{
// Chip select go low to start a flash command
cs_low();
// Write RST command = 0x99
uint8_t instruction = FLASH_CMD_RST;
m_buffer_tx[0] = instruction;
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,1);
// Chip select go high to end a flash command
cs_high();
return FlashOperationSuccess;
}
/*
* Function: CMD_WRSR
* Arguments: UpdateValue, 8/16 bit status register value to updata
* Description: The WRSR instruction is for changing the values of
* Status Register Bits (and configuration register)
* Return Message: FlashIsBusy, FlashTimeOut, FlashOperationSuccess
*/
//ReturnMsg cmd_wrsr( uint8_t UpdateValue )
//
//{
// // Check flash is busy or not
// if( IsFlashBusy() ) return FlashIsBusy;
//
// // Setting Write Enable Latch bit
// uint8_t err_code;
// err_code = cmd_wren();
//
// // Chip select go low to start a flash command
//// cs_low();
//
// // Send command and update value
//
// uint8_t instruction[9] = {0};
// instruction[0] = FLASH_CMD_WRSR;
// nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,m_buffer_rx,3);
// nrf_delay_ms(2);
// printf("UPDATE VALUE = %d",UpdateValue);
// instruction[1]=UpdateValue;
//// memcpy(instruction[1],UpdateValue,8);
// nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction[1],2,m_buffer_rx,4);
//
////#ifdef SUPPORT_WRSR_CR
//// SendByte( UpdateValue >> 8, SIO ); // write configuration register
////#endif
//
// // Chip select go high to end a flash command
// cs_high();
//
//
// if( WaitFlashReady( WriteStatusRegCycleTime ) )
// return FlashOperationSuccess;
// else
// return FlashTimeOut;
//
//}
ReturnMsg cmd_wrsr( uint8_t UpdateValue )
{
// Check flash is busy or not
if( IsFlashBusy() ) return FlashIsBusy;
// Setting Write Enable Latch bit
uint8_t err_code;
uint8_t read_value;
nrf_gpio_pin_clear(SPI_WP_PIN);
err_code = cmd_wren();
// Chip select go low to start a flash command
// cs_low();
// Send command and update value
err_code = cmd_rdsr(read_value);
printf("rdsr valu = %d \n",read_value);
if((read_value & 2)== 1)
{
uint8_t instruction[9] = {0};
instruction[0] = FLASH_CMD_WRSR;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,m_buffer_rx,3);
nrf_delay_ms(2);
printf("UPDATE VALUE = %d",UpdateValue);
instruction[1]=UpdateValue;
// memcpy(instruction[1],UpdateValue,8);
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction[1],2,m_buffer_rx,4);
err_code = cmd_rdsr(read_value);
printf("rdsr valu = %d \n",read_value);
if((read_value ^ 1)==1)
{
printf("wep is zero \n");
}
}
// uint8_t instruction[9] = {0};
// instruction[0] = FLASH_CMD_WRSR;
// nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,m_buffer_rx,3);
// nrf_delay_ms(2);
// printf("UPDATE VALUE = %d",UpdateValue);
// instruction[1]=UpdateValue;
//// memcpy(instruction[1],UpdateValue,8);
// nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction[1],2,m_buffer_rx,4);
//#ifdef SUPPORT_WRSR_CR
// SendByte( UpdateValue >> 8, SIO ); // write configuration register
//#endif
// Chip select go high to end a flash command
cs_high();
if( WaitFlashReady( WriteStatusRegCycleTime ) )
return FlashOperationSuccess;
else
return FlashTimeOut;
}
/*
* Function: CMD_RDSCUR
* Arguments: SecurityReg, 8 bit buffer to store security register value
* Description: The RDSCUR instruction is for reading the value of
* Security Register bits.
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_rdscur( uint8_t *SecurityReg )
{
uint8_t gDataBuffer;
// Chip select go low to start a flash command
cs_low();
//Send command
uint8_t instruction = FLASH_CMD_RDSCUR;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,gDataBuffer,3);
// Chip select go high to end a flash command
cs_high();
*SecurityReg = gDataBuffer;
return FlashOperationSuccess;
}
/*
* Function: CMD_WRSCUR
* Arguments: None.
* Description: The WRSCUR instruction is for changing the values of
* Security Register Bits.
* Return Message: FlashIsBusy, FlashOperationSuccess, FlashWriteRegFailed,
* FlashTimeOut
*/
ReturnMsg cmd_wrscur( void )
{
uint8_t gDataBuffer;
// Check flash is busy or not
if( IsFlashBusy() ) return FlashIsBusy;
// Setting Write Enable Latch bit
cmd_wren();
// Chip select go low to start a flash command
cs_low();
// Write WRSCUR command
uint8_t instruction = FLASH_CMD_WRSCUR;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,gDataBuffer,3);
// Chip select go high to end a flash command
cs_high();
if( WaitFlashReady( WriteSecuRegCycleTime ) ){
cmd_rdscur( &gDataBuffer );
// Check security register LDSO bit
if( (gDataBuffer & FLASH_LDSO_MASK) == FLASH_LDSO_MASK )
return FlashOperationSuccess;
else
return FlashWriteRegFailed;
}
else
return FlashTimeOut;
}
/*
* Function: CMD_RDID
* Arguments: Identification, 32 bit buffer to store id
* Description: The RDID instruction is to read the manufacturer ID
* of 1-byte and followed by Device ID of 2-byte.
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_rdid( uint32_t *Identification )
{
uint32_t temp;
uint8_t gDataBuffer[3];
// Chip select go low to start a flash command
cs_low();
// Send command
// SendByte( FLASH_CMD_RDID, SIO );
uint8_t instruction = FLASH_CMD_RDID;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,gDataBuffer,3);
// Chip select go high to end a command
cs_high();
// Store identification
temp = gDataBuffer[0];
temp = (temp << 8) | gDataBuffer[1];
*Identification = (temp << 8) | gDataBuffer[2];
printf("rdid = %x %x",gDataBuffer [0],gDataBuffer [1]);
return FlashOperationSuccess;
}
/*
* Function: CMD_RES
* Arguments: ElectricIdentification, 8 bit buffer to store electric id
* Description: The RES instruction is to read the Device
* electric identification of 1-byte.
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_res( uint8_t *ElectricIdentification )
{
printf("cmd_res \n");
// Chip select go low to start a flash command
cs_low();
// Send flash command and insert dummy cycle
uint8_t instruction[4];
instruction[0]= FLASH_CMD_RES;
instruction[1]= 0;
instruction[2]=0;
instruction[3]=0;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,4,m_buffer_rx,5);
// Get electric identification
*ElectricIdentification = m_buffer_rx[4];
printf(" eid = %x\n",m_buffer_rx[4]);
// Chip select go high to end a flash command
cs_high();
return FlashOperationSuccess;
}
/*
* Function: CMD_REMS
* Arguments: REMS_Identification, 16 bit buffer to store id
* fsptr, pointer of flash status structure
* Description: The REMS instruction is to read the Device
* manufacturer ID and electric ID of 1-byte.
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_rems( uint16_t *REMS_Identification, FlashStatus *fsptr )
{
uint8_t gDataBuffer[2];
// Chip select go low to start a flash command
cs_low();
// Send flash command and insert dummy cycle ( if need )
// ArrangeOpt = 0x00 will output the manufacturer's ID first
// = 0x01 will output electric ID first
// SendByte( FLASH_CMD_REMS, SIO );
// InsertDummyCycle( 16 );
// SendByte( fsptr->ArrangeOpt, SIO );
uint8_t instruction[4];
instruction[0]= FLASH_CMD_REMS;
instruction[1]= 0;
instruction[2]=0;
instruction[3]=0x00;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,4,m_buffer_rx,6);
// Get ID
gDataBuffer[0] = m_buffer_rx[2];//GetByte( SIO );
gDataBuffer[1] = m_buffer_rx[3];//GetByte( SIO );
// Store identification informaion
*REMS_Identification = (gDataBuffer[0] << 8) | gDataBuffer[1];
// Chip select go high to end a flash command
cs_high();
return FlashOperationSuccess;
}
void cmd_read( uint32_t flash_address, uint8_t *target_address, uint32_t byte_length )
{
uint32_t index;
uint8_t addr_4byte_mode;
// Check flash address
if( flash_address > FlashSize )
return FlashAddressInvalid;
nrf_delay_ms(5);
// Chip select go low to start a flash command
cs_low();
// Write READ command and address
uint8_t instruction;
instruction = FLASH_CMD_READ;
m_buffer_tx[0]= instruction;
m_buffer_tx[1] = flash_address >> 16;
m_buffer_tx[2] = flash_address >> 8;
m_buffer_tx[3] = flash_address;
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,FLASH_CMD_READ_LENGHT,m_data_receive,FLASH_CMD_READ_LENGHT+16);
// for( index=0; index < 4; index++ )
// {
// printf("m_buffer_tx[%d] = %.02x \n",index,m_buffer_tx[index]);
// nrf_delay_ms(10);
// }
// for( index=0; index < 20; index++ )
// {
// printf("m_data_receive[%d] = %.02x \n",index,m_data_receive[index]);
// nrf_delay_ms(10);
// }
// Chip select go high to end a flash command
nrf_delay_ms(500);
cs_high();
return true;
}
/*
* Function: Wait_Flash_WarmUp
* Arguments: None.
* Description: Wait some time until flash read / write enable.
* Return Message: None.
*/
void wait_flash_warm_up()
{
uint32_t time_cnt = FlashFullAccessTime;
while( time_cnt > 0 )
{
time_cnt--;
}
}
uint8_t flash_ID_test( uint8_t id )
{
uint8_t instruction[8] = {0};
uint8_t id_read = id;
switch (id_read)
{
case 1:
instruction[0] = FLASH_CMD_RES ;
instruction[1]= 0x00;
instruction[2] = 0x00;
instruction[3]= 0x00;
cs_low();
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,4,m_buffer_rx,5);
nrf_delay_ms(1);
printf("\rValue is 1:");
printf("%02x,%02x,%02x,%02x,%02x,%02x,%02x \n",m_buffer_rx[0],m_buffer_rx[1],m_buffer_rx[2],m_buffer_rx[3],m_buffer_rx[4],m_buffer_rx[5],m_buffer_rx[6]);
cs_high();
break;
case 2:
instruction[0] = FLASH_CMD_REMS ;
instruction[1]= 0x01;
instruction[2] = 0x02;
instruction[3]= 0x00;
printf("\rValue is 2:");
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,4,m_buffer_rx,6);
nrf_delay_ms(2);
printf("%02x,%02x,%02x,%02x,%02x,%02x\n",m_buffer_rx[0],m_buffer_rx[1],m_buffer_rx[2],m_buffer_rx[3],m_buffer_rx[4],m_buffer_rx[5]);
break;
case 3:
m_buffer_tx[0] = FLASH_CMD_RDID;
cs_low();
// nrf_gpio_pin_clear(SPI_SS_PIN);
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,4);
//nrf_delay_ms(2);
//nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,3);
nrf_delay_ms(2);
printf("\rValue is 3:");
printf("%02x,%02x,%02x\n",m_buffer_rx[1],m_buffer_rx[2],m_buffer_rx[3]);
// nrf_gpio_pin_set(SPI_SS_PIN);
cs_high();
break;
default:
printf("Out of range");
break;
}
return true;
}
ReturnMsg cmd_rdsr( uint8_t *StatusReg )
{
uint8_t gDataBuffer;
// Chip select go low to start a flash command
cs_low();
// Send command
nrf_drv_spi_transfer(&spi,FLASH_CMD_RDSR,1,gDataBuffer,1);
// Chip select go high to end a flash command
cs_high();
*StatusReg = gDataBuffer;
// printf("cmd_rdsr = %d \n",gDataBuffer);
return FlashOperationSuccess;
}
ReturnMsg cmd_rdcr( uint8_t *StatusReg )
{
uint8_t gDataBuffer;
// Chip select go low to start a flash command
cs_low();
// Send command
// SendByte( FLASH_CMD_RDSR, SIO );
// gDataBuffer = GetByte( SIO );
nrf_drv_spi_transfer(&spi,FLASH_CMD_RDCR,1,gDataBuffer,1);
// Chip select go high to end a flash command
cs_high();
*StatusReg = gDataBuffer;
// printf("status register = %x \n",StatusReg);
return FlashOperationSuccess;
}
bool IsFlashBusy( void )
{
uint8_t gDataBuffer;
cmd_rdsr( &gDataBuffer );
if( (gDataBuffer & FLASH_WIP_MASK) == FLASH_WIP_MASK )
return true;
else
return false;
}
bool WaitFlashReady( uint32_t ExpectTime )
{
uint32_t temp = 0;
while( IsFlashBusy() )
{
if( temp > ExpectTime )
{
return false;
}
temp = temp + 1;
}
return true;
}
ReturnMsg cmd_wren( void )
{
// Chip select go low to start a flash command
cs_low();
// Write Enable command = 0x06, Setting Write Enable Latch Bit
uint8_t instruction = FLASH_CMD_WREN;
m_buffer_tx[0] = instruction;
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,1);
// Chip select go high to end a flash command
cs_high();
return FlashOperationSuccess;
}
ReturnMsg cmd_wrdis( void )
{
// Chip select go low to start a flash command
cs_low();
// Write Enable command = 0x06, Setting Write Enable Latch Bit
uint8_t instruction = FLASH_CMD_WRDI;
m_buffer_tx[0] = instruction;
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,1);
// Chip select go high to end a flash command
cs_high();
return FlashOperationSuccess;
}
ReturnMsg cmd_pp( uint32_t flash_address, uint8_t *source_address, uint32_t byte_length )
{
uint32_t index;
// Check flash address
if( flash_address > FLASH_SIZE ) return FlashAddressInvalid;
//
// // Check flash is busy or not
if( IsFlashBusy() ) return FlashIsBusy;
// Setting Write Enable Latch bit
cmd_wren();
nrf_delay_ms(5);
// Chip select go low to start a flash command
cs_low();
nrf_delay_ms(100);
// Write Page Program command
uint8_t len = 4;
m_buffer_tx[0]=FLASH_CMD_PP;
// memcpy(m_buffer_tx,instruction,4);
// nrf_drv_spi_transfer(&spi,instruction,len,m_buffer_rx,len+1);
memcpy(m_buffer_tx[4],flash_address >> 16,1);
m_buffer_tx[1] = flash_address >> 16;
m_buffer_tx[2] = flash_address >> 8;
m_buffer_tx[3] = flash_address;
for( index=4; index < 20; index++ )
{
m_buffer_tx[index] = source_address[index];//0xaa;
}
printf("\r data transmitted: ");
for( index=0; index < 20; index++ )
{
printf(" %.02x ",m_buffer_tx[index]);
nrf_delay_ms(10);
}
printf("\n");
// nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,20,m_data_receive,40);
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,20,m_data_receive,0);
// Chip select go high to end a flash command
cs_high();
if( WaitFlashReady( PageProgramCycleTime ) )
return FlashOperationSuccess;
else
return FlashTimeOut;
}
uint8_t cmd_se( uint32_t flash_address )
{
// Check flash address
if( flash_address > FLASH_SIZE ) return FlashAddressInvalid;
// Check flash is busy or not
if( IsFlashBusy() ) return FlashIsBusy;
// Setting Write Enable Latch bit
cmd_wren();
// Chip select go low to start a flash command
cs_low();
//Write Sector Erase command = 0x20;
m_buffer_tx[0] = FLASH_CMD_SE;
m_buffer_tx[1] = flash_address >> 16;
m_buffer_tx[2] = flash_address >> 8;
m_buffer_tx[3] = flash_address;
printf(" \r sectore esrase command : %0.2x,%0.2x,%0.2x,%0.2x\n ",m_buffer_tx[0],m_buffer_tx[1],m_buffer_tx[2],m_buffer_tx[3]);
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,4,m_buffer_rx,4);
// Chip select go high to end a flash command
cs_high();
// if( WaitFlashReady( SectorEraseCycleTime ) )
if( WaitFlashReady( 240000000 ))
{
cmd_rdscur(SecurityReg);
printf("SecurityReg %d \n ",SecurityReg);
return FlashOperationSuccess;
}
else
return FlashTimeOut;
}
uint8_t cmd_block_erase( uint32_t flash_address )
{
// Check flash address
if( flash_address > FLASH_SIZE ) return FlashAddressInvalid;
// Check flash is busy or not
if( IsFlashBusy() ) return FlashIsBusy;
// Setting Write Enable Latch bit
// cmd_wren();
// Chip select go low to start a flash command
cs_low();
//Write Sector Erase command = 0x20;
uint8_t instruction;
instruction= FLASH_CMD_SE;
// instruction[1]= 0;
// instruction[2] =0;
// instruction[3]=0;
m_buffer_tx[0] = instruction;
// memcpy(m_buffer_tx,instruction,4);
m_buffer_tx[1] = flash_address >> 16;
m_buffer_tx[2] = flash_address >> 8;
m_buffer_tx[3] = flash_address;
// SendByte( FLASH_CMD_SE, SIO );
// SendFlashAddr( flash_address, SIO, addr_4byte_mode );
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,4,m_buffer_rx,4);
// Chip select go high to end a flash command
cs_high();
if( WaitFlashReady( SectorEraseCycleTime ) )
return FlashOperationSuccess;
else
return FlashTimeOut;
}
/*
* Function: CMD_CE
* Arguments: None.
* Description: The CE instruction is for erasing the data
* of the whole chip to be "1".
* Return Message: FlashIsBusy, FlashOperationSuccess, FlashTimeOut
*/
ReturnMsg cmd_ce( void )
{
// Check flash is busy or not
if( IsFlashBusy() ) return FlashIsBusy;
// Setting Write Enable Latch bit
cmd_wren();
// Chip select go low to start a flash command
cs_low();
nrf_delay_ms(100);
//Write Chip Erase command = 0x60;
m_buffer_tx[0] = 0xC7;//FLASH_CMD_CE;
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,0);
// Chip select go high to end a flash command
cs_high();
// cmd_rdsr(StatusReg);
// printf("StatusReg= %d \n",StatusReg);
//if( WaitFlashReady( 60000 ) )
nrf_delay_ms(60000);
return FlashOperationSuccess;
// else
// return FlashTimeOut;
//return FlashOperationSuccess;
}
/*
* Simple flash read/write test
*/
uint8_t flash_read_write_test( void )
{
uint8_t message= 0;
FlashStatus flash_state = {0};
uint32_t flash_addr;
uint32_t trans_len = 0;
uint16_t i=0, error_cnt = 0;
uint16_t seed = 0;
uint8_t st_reg = 0;
/* Assign initial condition */
flash_addr = FLASH_TARGET_ADDR;
trans_len = TRANS_LENGTH;
seed = RANDOM_SEED;
/* Erase 4K sector of flash memory
Note: It needs to erase dirty sector before program */
uint8_t err_code;
// err_code = cmd_ce();//cmd_block_erase(flash_addr);//cmd_se( flash_addr );
// printf("error code = %d \n",err_code);
// nrf_delay_ms(300);
// cmd_read( flash_addr, m_data_receive, TRANS_LENGTH );
// nrf_delay_ms(300);
//
// printf("\r data after chip erase: ");
// for( i=4; i < 20; i++ )
// {
// printf(" %.02x ",m_data_receive[i]);
// nrf_delay_ms(10);
// }
// printf("\n");
/* Program data to flash memory */
cmd_pp( flash_addr, m_data_send, TRANS_LENGTH );
nrf_delay_ms(100);
/* Read flash memory data to memory buffer */
cmd_read( flash_addr, m_data_receive, TRANS_LENGTH );
nrf_delay_ms(300);
/* Compare original data and flash data */
// for( i=4; i < (trans_len); i=i+1 )
// {
// if( m_data_send[i] != m_data_receive[i] )
// {
// printf("wrong data \n");
// Error_inc( error_cnt );
// }
// else
// {
printf("\r data received: ");
for( i=4; i < 20; i++ )
{
printf(" %.02x ",m_data_receive[i]);
nrf_delay_ms(10);
}
printf("\n");
// }
// }
/* Erase 4K sector of flash memory */
cmd_ce();//cmd_block_erase(flash_addr); //cmd_se( flash_addr );
nrf_delay_ms(240); //240 60000
if( error_cnt != 0 )
return false;
else
return true;
}
uint8_t ext_flash_init(void)
{
uint8_t retval = false;
/* Configure SPI pins */
nrf_drv_spi_config_t spi_config = NRF_DRV_SPI_DEFAULT_CONFIG;
spi_config.ss_pin = SPI_SS_PIN;
spi_config.miso_pin = SPI_MISO_PIN;
spi_config.mosi_pin = SPI_MOSI_PIN;
spi_config.sck_pin = SPI_SCK_PIN;
spi_config.mode = NRF_DRV_SPI_MODE_0;
spi_config.frequency= NRF_DRV_SPI_FREQ_125K;
APP_ERROR_CHECK(nrf_drv_spi_init(&spi, &spi_config, spi_event_handler, NULL));
nrf_gpio_pin_set(SPI_WP_PIN);
uint8_t err_code;
cmd_rsten();
cmd_rst();
err_code = cmd_wrdis();
/* Set CS pin to High*/
// cs_high();
wait_flash_warm_up();
nrf_delay_ms(100);
flash_ID_test(2);
/* read and verify manufacturer and device id from external flash to ensure external flash is working */
if(flash_ID_test(2) == true)
{
return true;
}
return retval;
}
Hi
Did you really need a 100ms delay after chip select to make it work?
Did you try to measure how long the status is busy after issuing an erase command?
According to the specification this can take several seconds, depending on how much you are erasing.
I realized you're using a similar flash device to the one used on the nRF52840DK, which allows me to do some testing myself.
Are you able to send me both your source and header files so I can try to run your code?
The code you sent is referencing some includes and defines that I don't have.
Best regards
Torbjørn
Hi
Did you really need a 100ms delay after chip select to make it work?
Did you try to measure how long the status is busy after issuing an erase command?
According to the specification this can take several seconds, depending on how much you are erasing.
I realized you're using a similar flash device to the one used on the nRF52840DK, which allows me to do some testing myself.
Are you able to send me both your source and header files so I can try to run your code?
The code you sent is referencing some includes and defines that I don't have.
Best regards
Torbjørn
Did you really need a 100ms delay after chip select to make it work? - No but to try to get the chip erase working I added that delay . But now when I removed it it is working. But I am not sure enough that whether it will work always or not.
I realized you're using a similar flash device to the one used on the nRF52840DK- Yes its a similar flash with difference in its storage capacity .(16 MB)
I have made removed that 100ms delay after CS and also removed the flash busy and wait status which I think is necessary but after doing that I am able to get the results sometimes. So I think it still needs some modifications for its proper functioning. I am attaching my source code for your reference.I am using SDK 15.3.0ble_app_uart_pdm_extflash.rar
Hi
Thanks for sharing your project. It mostly seems to work fine, except the external_flash.c/h files appear to be missing.
Most likely you put these in one of the SDK folders.
Are you able to share these files also?
Best regards
Torbjørn
Opps, Sorry for the inconvience. I am sharing these two files. One more thing I have doubt is that I am not able to write more than 16 bytes and also do not know the what the
///**
// ******************************************************************************
// * @file ext_flash.c
// * This source file provides external flash memory related functionalities.
// *
// * @author Glide Embedded Technology <www.glidemtech.com>
// * @date 7, August, 2019
// ******************************************************************************
// */
//
///* Includes ------------------------------------------------------------------*/
///* Includes ------------------------------------------------------------------*/
#include <stdio.h>
#include <string.h>
#include <stdint.h>
//
#include "external_flash.h"
#include <hal/nrf_gpio.h>
#include <hal/nrf_spi.h>
#include "nrf_drv_spi.h"
#include "nrf_log.h"
#include "nrf_log_ctrl.h"
#include "nrf_log_default_backends.h"
#include "nrf_delay.h"
uint8_t print = 1;
#define SPI_INSTANCE 0 /**< SPI instance index. */
static const nrf_drv_spi_t spi = NRF_DRV_SPI_INSTANCE(SPI_INSTANCE);
#define WAIT_FOR_PERIPH() do { \
while (!m_finished) {} \
m_finished = false; \
} while (0)
static volatile bool m_finished = false;
static uint8_t m_buffer_tx[256];
static uint8_t m_buffer_rx[256];
//static uint8_t m_data_send[256];
static uint8_t m_data_receive[256];
#define TEST_STRING "Z" //"Nordic"
static uint8_t m_tx_buf[] = TEST_STRING; /**< TX buffer. */
static uint8_t m_rx_buf[sizeof(TEST_STRING) + 1]; /**< RX buffer. */
static const uint8_t m_length = sizeof(m_tx_buf);
static uint8_t m_buffer_tx[256];
static uint8_t m_buffer_rx[256];
//int16_t pcm_data_buffer[MEM_SIZE_15KB] = {0};
static uint16_t pcm_data_buffer[MEM_SIZE_15KB];
//static uint8_t m_data_send[256];
static uint8_t m_data_receive[256];
static uint8_t m_data_send[225] = {[0 ... 224] = 0xcd};
uint8_t StatusReg;
uint8_t ConfigReg;
uint8_t SecurityReg;
/**
* @brief SPI user event handler.
* @param event
*/
void spi_event_handler(nrf_drv_spi_evt_t const * p_event,
void * p_context)
{
m_finished = true;
uint16_t i ;
//printf("\n\rTransfer completed.");
if (m_buffer_rx[0] != 0)
{
// printf(" Received:");
for(i=0;i<8;i++)
{
// printf("m_buffer_rx[%d] = %x ",i,m_buffer_rx[i]);
}
NRF_LOG_HEXDUMP_INFO(m_buffer_rx, strlen((const char *)m_buffer_rx));
}
// nrf_gpio_pin_set(SPI_SS_PIN);
}
void cs_low(void)
{
// nrf_gpio_pin_set(SPI_SS_PIN);
nrf_gpio_pin_clear(SPI_SS_PIN);
}
void cs_high(void)
{
// nrf_gpio_pin_clear(SPI_SS_PIN);
nrf_gpio_pin_set(SPI_SS_PIN);
}
/*
* Reset setting Command
*/
/*
* Function: CMD_RSTEN
* Arguments: None.
* Description: Enable RST command
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_rsten( void )
{
// Chip select go low to start a flash command
cs_low();
// Write RSTEN command
uint8_t instruction = FLASH_CMD_RSTEN;
m_buffer_tx[0] = instruction;
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,1);
// Chip select go high to end a flash command
cs_high();
return FlashOperationSuccess;
}
/*
* Function: CMD_RST
* Arguments: fsptr, pointer of flash status structure
* Description: The RST instruction is used as a system (software) reset that
* puts the device in normal operating Ready mode.
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_rst( void )
{
// Chip select go low to start a flash command
cs_low();
// Write RST command = 0x99
uint8_t instruction = FLASH_CMD_RST;
m_buffer_tx[0] = instruction;
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,1);
// Chip select go high to end a flash command
cs_high();
return FlashOperationSuccess;
}
/*
* Function: CMD_WRSR
* Arguments: UpdateValue, 8/16 bit status register value to updata
* Description: The WRSR instruction is for changing the values of
* Status Register Bits (and configuration register)
* Return Message: FlashIsBusy, FlashTimeOut, FlashOperationSuccess
*/
ReturnMsg cmd_wrsr( uint8_t UpdateValue )
{
// Check flash is busy or not
if( IsFlashBusy() ) return FlashIsBusy;
// Setting Write Enable Latch bit
uint8_t err_code;
err_code = cmd_wren();
// Chip select go low to start a flash command
// cs_low();
// Send command and update value
uint8_t instruction[9] = {0};
instruction[0] = FLASH_CMD_WRSR;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,m_buffer_rx,3);
nrf_delay_ms(2);
printf("UPDATE VALUE = %d",UpdateValue);
instruction[1]=UpdateValue;
// memcpy(instruction[1],UpdateValue,8);
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction[1],2,m_buffer_rx,4);
//#ifdef SUPPORT_WRSR_CR
// SendByte( UpdateValue >> 8, SIO ); // write configuration register
//#endif
// Chip select go high to end a flash command
cs_high();
if( WaitFlashReady( WriteStatusRegCycleTime ) )
return FlashOperationSuccess;
else
return FlashTimeOut;
}
//
//ReturnMsg cmd_wrsr( uint8_t UpdateValue )
//
//{
// // Check flash is busy or not
// if( IsFlashBusy() ) return FlashIsBusy;
//
// // Setting Write Enable Latch bit
// uint8_t err_code;
// uint8_t read_value;
// nrf_gpio_pin_clear(SPI_WP_PIN);
// err_code = cmd_wren();
//
// // Chip select go low to start a flash command
//// cs_low();
//
// // Send command and update value
// err_code = cmd_rdsr(read_value);
// printf("rdsr valu = %d \n",read_value);
// if((read_value & 2)== 1)
// {
// uint8_t instruction[9] = {0};
// instruction[0] = FLASH_CMD_WRSR;
// nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,m_buffer_rx,3);
// nrf_delay_ms(2);
// printf("UPDATE VALUE = %d",UpdateValue);
// instruction[1]=UpdateValue;
//// memcpy(instruction[1],UpdateValue,8);
// nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction[1],2,m_buffer_rx,4);
//
// err_code = cmd_rdsr(read_value);
// printf("rdsr valu = %d \n",read_value);
// if((read_value ^ 1)==1)
// {
// printf("wep is zero \n");
//
// }
//
// }
//
//
//// uint8_t instruction[9] = {0};
//// instruction[0] = FLASH_CMD_WRSR;
//// nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,m_buffer_rx,3);
//// nrf_delay_ms(2);
//// printf("UPDATE VALUE = %d",UpdateValue);
//// instruction[1]=UpdateValue;
////// memcpy(instruction[1],UpdateValue,8);
//// nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction[1],2,m_buffer_rx,4);
//
////#ifdef SUPPORT_WRSR_CR
//// SendByte( UpdateValue >> 8, SIO ); // write configuration register
////#endif
//
// // Chip select go high to end a flash command
// cs_high();
//
//
// if( WaitFlashReady( WriteStatusRegCycleTime ) )
// return FlashOperationSuccess;
// else
// return FlashTimeOut;
//
//}
/*
* Function: CMD_RDSCUR
* Arguments: SecurityReg, 8 bit buffer to store security register value
* Description: The RDSCUR instruction is for reading the value of
* Security Register bits.
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_rdscur( uint8_t *SecurityReg )
{
uint8_t gDataBuffer;
// Chip select go low to start a flash command
cs_low();
//Send command
uint8_t instruction = FLASH_CMD_RDSCUR;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,gDataBuffer,3);
// Chip select go high to end a flash command
cs_high();
*SecurityReg = gDataBuffer;
return FlashOperationSuccess;
}
/*
* Function: CMD_WRSCUR
* Arguments: None.
* Description: The WRSCUR instruction is for changing the values of
* Security Register Bits.
* Return Message: FlashIsBusy, FlashOperationSuccess, FlashWriteRegFailed,
* FlashTimeOut
*/
ReturnMsg cmd_wrscur( void )
{
uint8_t gDataBuffer;
// Check flash is busy or not
if( IsFlashBusy() ) return FlashIsBusy;
// Setting Write Enable Latch bit
cmd_wren();
// Chip select go low to start a flash command
cs_low();
// Write WRSCUR command
uint8_t instruction = FLASH_CMD_WRSCUR;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,gDataBuffer,3);
// Chip select go high to end a flash command
cs_high();
if( WaitFlashReady( WriteSecuRegCycleTime ) ){
cmd_rdscur( &gDataBuffer );
// Check security register LDSO bit
if( (gDataBuffer & FLASH_LDSO_MASK) == FLASH_LDSO_MASK )
return FlashOperationSuccess;
else
return FlashWriteRegFailed;
}
else
return FlashTimeOut;
}
/*
* Function: CMD_RDID
* Arguments: Identification, 32 bit buffer to store id
* Description: The RDID instruction is to read the manufacturer ID
* of 1-byte and followed by Device ID of 2-byte.
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_rdid( uint32_t *Identification )
{
uint32_t temp;
uint8_t gDataBuffer[3];
// Chip select go low to start a flash command
cs_low();
// Send command
// SendByte( FLASH_CMD_RDID, SIO );
uint8_t instruction = FLASH_CMD_RDID;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,1,gDataBuffer,3);
// Chip select go high to end a command
cs_high();
// Store identification
temp = gDataBuffer[0];
temp = (temp << 8) | gDataBuffer[1];
*Identification = (temp << 8) | gDataBuffer[2];
printf("rdid = %x %x",gDataBuffer [0],gDataBuffer [1]);
return FlashOperationSuccess;
}
/*
* Function: CMD_RES
* Arguments: ElectricIdentification, 8 bit buffer to store electric id
* Description: The RES instruction is to read the Device
* electric identification of 1-byte.
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_res( uint8_t *ElectricIdentification )
{
printf("cmd_res \n");
// Chip select go low to start a flash command
cs_low();
// Send flash command and insert dummy cycle
uint8_t instruction[4];
instruction[0]= FLASH_CMD_RES;
instruction[1]= 0;
instruction[2]=0;
instruction[3]=0;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,4,m_buffer_rx,5);
// Get electric identification
*ElectricIdentification = m_buffer_rx[4];
printf(" eid = %x\n",m_buffer_rx[4]);
// Chip select go high to end a flash command
cs_high();
return FlashOperationSuccess;
}
/*
* Function: CMD_REMS
* Arguments: REMS_Identification, 16 bit buffer to store id
* fsptr, pointer of flash status structure
* Description: The REMS instruction is to read the Device
* manufacturer ID and electric ID of 1-byte.
* Return Message: FlashOperationSuccess
*/
ReturnMsg cmd_rems( uint16_t *REMS_Identification, FlashStatus *fsptr )
{
uint8_t gDataBuffer[2];
// Chip select go low to start a flash command
cs_low();
// Send flash command and insert dummy cycle ( if need )
// ArrangeOpt = 0x00 will output the manufacturer's ID first
// = 0x01 will output electric ID first
// SendByte( FLASH_CMD_REMS, SIO );
// InsertDummyCycle( 16 );
// SendByte( fsptr->ArrangeOpt, SIO );
uint8_t instruction[4];
instruction[0]= FLASH_CMD_REMS;
instruction[1]= 0;
instruction[2]=0;
instruction[3]=0x00;
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,4,m_buffer_rx,6);
// Get ID
gDataBuffer[0] = m_buffer_rx[2];//GetByte( SIO );
gDataBuffer[1] = m_buffer_rx[3];//GetByte( SIO );
// Store identification informaion
*REMS_Identification = (gDataBuffer[0] << 8) | gDataBuffer[1];
// Chip select go high to end a flash command
cs_high();
return FlashOperationSuccess;
}
void cmd_read( uint32_t flash_address, uint16_t *target_address, uint32_t byte_length )
{
uint32_t index;
// Check flash address
if( flash_address > FlashSize )
return FlashAddressInvalid;
// cmd_wrdis();
// nrf_delay_ms(100);
// Chip select go low to start a flash command
cs_low();
// nrf_delay_ms(50);
// Write READ command and address
memset(m_buffer_tx,0x00,sizeof(m_buffer_tx));
uint8_t instruction;
instruction = FLASH_CMD_READ;
m_buffer_tx[0]= instruction;
m_buffer_tx[1] = flash_address >> 16;
m_buffer_tx[2] = flash_address >> 8;
m_buffer_tx[3] = flash_address;
// nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,FLASH_CMD_READ_LENGHT,m_data_receive,FLASH_CMD_READ_LENGHT+16);
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,FLASH_CMD_READ_LENGHT,m_data_receive,FLASH_CMD_READ_LENGHT+byte_length);
// for( index=0; index < 4; index++ )
// {
// printf("m_buffer_tx[%d] = %.02x \n",index,m_buffer_tx[index]);
// nrf_delay_ms(10);
// }
// for( index=0; index < 20; index++ )
// {
// printf("m_data_receive[%d] = %.02x \n",index,m_data_receive[index]);
// nrf_delay_ms(10);
// }
// Chip select go high to end a flash command
nrf_delay_ms(50);
cs_high();
return true;
}
void read_data_ext_flash(void)
{
uint8_t i;
static uint32_t flash_address = FLASH_TARGET_ADDR;
static counter=0;
for(i=0;i<16;i++)
// for(i=0;i<2;i++)
{
// for(j=0;j<256;j=j+2)
{
cmd_read(flash_address,pcm_data_buffer,225);
uint16_t index;
nrf_delay_ms(5);
// for( index=0; index < 102400; index++ )
for( index=0; index < 225; index++ )
{
// Read data one byte at a time
printf("\r\n%2.2X%2.2X",pcm_data_buffer[index],pcm_data_buffer[index+1]);
index = index+1;
}
// nrf_delay_ms(10);
}
flash_address = flash_address + 0x000100;
// counter ++;
}
// uint32_t flash_address = FLASH_TARGET_ADDR;
//// cmd_read(flash_address,pcm_data_buffer,102400);
// cmd_read(flash_address,pcm_data_buffer,3584); //256*16 3584 bytes
// for( index=0; index < 102400; index++ )
// for( index=0; index < MEM_SIZE_15KB; index++ )
// {
// // Read data one byte at a time
//
// printf("\r\n%2.2X%2.2X",pcm_data_buffer[index],pcm_data_buffer[index+1]);
// index = index+1;
//
// }
//
// for( index=0; index < MEM_SIZE_15KB; index++ )
//// {
//// // Read data one byte at a time
////
// printf("\r\n%2.2X%",pcm_data_buffer[index]);
// index = index+1;
//
// }
}
/*
* Function: Wait_Flash_WarmUp
* Arguments: None.
* Description: Wait some time until flash read / write enable.
* Return Message: None.
*/
void wait_flash_warm_up()
{
uint32_t time_cnt = FlashFullAccessTime;
while( time_cnt > 0 )
{
time_cnt--;
}
}
uint8_t flash_ID_test( uint8_t id )
{
uint8_t instruction[8] = {0};
uint8_t id_read = id;
switch (id_read)
{
case 1:
instruction[0] = FLASH_CMD_RES ;
instruction[1]= 0x00;
instruction[2] = 0x00;
instruction[3]= 0x00;
cs_low();
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,4,m_buffer_rx,5);
nrf_delay_ms(1);
printf("\rValue is 1:");
printf("%02x \n",m_buffer_rx[4]);
cs_high();
break;
case 2:
instruction[0] = FLASH_CMD_REMS ;
instruction[1]= 0x01;
instruction[2] = 0x02;
instruction[3]= 0x00;
printf("\rValue is 2:");
memset(m_buffer_rx,0x00,sizeof(m_buffer_rx));
nrf_drv_spi_transfer(&spi,(uint8_t const *)instruction,4,m_buffer_rx,6);
nrf_delay_ms(2);
printf("%02x,%02x,%02x,%02x,%02x,%02x\n",m_buffer_rx[0],m_buffer_rx[1],m_buffer_rx[2],m_buffer_rx[3],m_buffer_rx[4],m_buffer_rx[5]);
// printf("%d,%d,%d,%d,%d,%d\n",m_buffer_rx[0],m_buffer_rx[1],m_buffer_rx[2],m_buffer_rx[3],m_buffer_rx[4],m_buffer_rx[5]);
break;
case 3:
m_buffer_tx[0] = FLASH_CMD_RDID;
cs_low();
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,4);
nrf_delay_ms(2);
printf("\rValue is 3:");
printf("%02x,%02x,%02x\n",m_buffer_rx[1],m_buffer_rx[2],m_buffer_rx[3]);
// printf("%d,%d,%d \n",m_buffer_rx[1],m_buffer_rx[2],m_buffer_rx[3]);
cs_high();
break;
default:
printf("Out of range");
break;
}
return true;
}
ReturnMsg cmd_rdsr( uint8_t *StatusReg )
{
uint8_t gDataBuffer;
// Chip select go low to start a flash command
cs_low();
// Send command
nrf_drv_spi_transfer(&spi,FLASH_CMD_RDSR,1,gDataBuffer,1);
// Chip select go high to end a flash command
cs_high();
*StatusReg = gDataBuffer;
// printf("cmd_rdsr = %d \n",gDataBuffer);
return FlashOperationSuccess;
}
ReturnMsg cmd_rdcr( uint8_t *StatusReg )
{
uint8_t gDataBuffer;
// Chip select go low to start a flash command
cs_low();
// Send command
// SendByte( FLASH_CMD_RDSR, SIO );
// gDataBuffer = GetByte( SIO );
nrf_drv_spi_transfer(&spi,FLASH_CMD_RDCR,1,gDataBuffer,1);
// Chip select go high to end a flash command
cs_high();
*StatusReg = gDataBuffer;
// printf("status register = %x \n",StatusReg);
return FlashOperationSuccess;
}
bool IsFlashBusy( void )
{
uint8_t gDataBuffer;
cmd_rdsr( &gDataBuffer );
if( (gDataBuffer & FLASH_WIP_MASK) == FLASH_WIP_MASK )
return true;
else
return false;
}
bool WaitFlashReady( uint32_t ExpectTime )
{
uint32_t temp = 0;
while( IsFlashBusy() )
{
if( temp > ExpectTime )
{
return false;
}
temp = temp + 1;
}
return true;
}
ReturnMsg cmd_wren( void )
{
// // Chip select go low to start a flash command
// cs_low();
memset(m_buffer_tx,0x00,sizeof(m_buffer_tx));
// Write Enable command = 0x06, Setting Write Enable Latch Bit
uint8_t instruction = FLASH_CMD_WREN;
m_buffer_tx[0] = instruction;
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,0);
// Chip select go high to end a flash command
// cs_high();
return FlashOperationSuccess;
}
ReturnMsg cmd_wrdis( void )
{
// Chip select go low to start a flash command
cs_low();
// Write Enable command = 0x06, Setting Write Enable Latch Bit
uint8_t instruction = FLASH_CMD_WRDI;
m_buffer_tx[0] = instruction;
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,1);
// Chip select go high to end a flash command
cs_high();
return FlashOperationSuccess;
}
ReturnMsg cmd_pp( uint32_t flash_address, uint16_t *source_address, uint32_t byte_length )
{
// printf("cmd_pp \n");
uint32_t index;
// Check flash address
if( flash_address > FLASH_SIZE ) return FlashAddressInvalid;
//
// // Check flash is busy or not
// if( IsFlashBusy() ) return FlashIsBusy;
nrf_delay_ms(10);
// Chip select go low to start a flash command
cs_low();
// Setting Write Enable Latch bit
cmd_wren();
nrf_delay_ms(3);
// Write Page Program command
uint8_t len = 4;
m_buffer_tx[0]=FLASH_CMD_PP;
// memcpy(m_buffer_tx,instruction,4);
// nrf_drv_spi_transfer(&spi,instruction,len,m_buffer_rx,len+1);
memcpy(m_buffer_tx[4],flash_address >> 16,1);
m_buffer_tx[1] = flash_address >> 16;
m_buffer_tx[2] = flash_address >> 8;
m_buffer_tx[3] = flash_address;
for( index=4; index < byte_length; index++ )
{
m_buffer_tx[index] = (uint8_t) source_address[index];//0xaa;
}
printf("\r data transmitted: ");
for( index=0; index < 30; index++ )
{
printf(" %.02x ",m_buffer_tx[index]);
nrf_delay_ms(10);
}
printf("\n");
// nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,20,m_data_receive,0);
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,251,m_data_receive,0);
// Chip select go high to end a flash command
nrf_delay_ms(50);
cs_high();
nrf_delay_ms(20);
if( WaitFlashReady( PageProgramCycleTime ) )
return FlashOperationSuccess;
else
return FlashTimeOut;
}
uint8_t cmd_se( uint32_t flash_address )
{
// Check flash address
if( flash_address > FLASH_SIZE ) return FlashAddressInvalid;
// Check flash is busy or not
if( IsFlashBusy() ) return FlashIsBusy;
// Chip select go low to start a flash command
cs_low();
// Setting Write Enable Latch bit
cmd_wren();
nrf_delay_ms(3);
// nrf_delay_ms(100);
//Write Sector Erase command = 0x20;
m_buffer_tx[0] = FLASH_CMD_SE;
m_buffer_tx[1] = flash_address >> 16;
m_buffer_tx[2] = flash_address >> 8;
m_buffer_tx[3] = flash_address;
// printf(" \r sectore esrase command : %0.2x,%0.2x,%0.2x,%0.2x\n ",m_buffer_tx[0],m_buffer_tx[1],m_buffer_tx[2],m_buffer_tx[3]);
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,4,m_buffer_rx,0);
// Chip select go high to end a flash command
nrf_delay_ms(50);
cs_high();
nrf_delay_ms(240);
printf("sector esrsed \n");
// if( WaitFlashReady( SectorEraseCycleTime ) )
// if( WaitFlashReady( 240000000 ))
// cmd_rdsr(StatusReg);
return FlashOperationSuccess;
// else
// return FlashTimeOut;
}
uint8_t cmd_block_erase( uint32_t flash_address )
{
// Check flash address
if( flash_address > FLASH_SIZE ) return FlashAddressInvalid;
// Check flash is busy or not
// if( IsFlashBusy() ) return FlashIsBusy;
// Chip select go low to start a flash command
cs_low();
// Setting Write Enable Latch bit
cmd_wren();
nrf_delay_ms(3);
//Write Sector Erase command = 0x20;
uint8_t instruction;
instruction= FLASH_CMD_BE;
// instruction[1]= 0;
// instruction[2] =0;
// instruction[3]=0;
m_buffer_tx[0] = instruction;
// memcpy(m_buffer_tx,instruction,4);
m_buffer_tx[1] = flash_address >> 16;
m_buffer_tx[2] = flash_address >> 8;
m_buffer_tx[3] = flash_address;
// SendByte( FLASH_CMD_SE, SIO );
// SendFlashAddr( flash_address, SIO, addr_4byte_mode );
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,4,m_buffer_rx,0);
// Chip select go high to end a flash command
nrf_delay_ms(100);
cs_high();
nrf_delay_ms(4000);
printf("block earsed \n");
// if( WaitFlashReady( SectorEraseCycleTime ) )
return FlashOperationSuccess;
// else
// return FlashTimeOut;
}
/*
* Function: CMD_CE
* Arguments: None.
* Description: The CE instruction is for erasing the data
* of the whole chip to be "1".
* Return Message: FlashIsBusy, FlashOperationSuccess, FlashTimeOut
*/
ReturnMsg cmd_ce( void )
{
// Check flash is busy or not
// if( IsFlashBusy() ) return FlashIsBusy;
// Chip select go low to start a flash command
cs_low();
// Setting Write Enable Latch bit
cmd_wren();
nrf_delay_ms(3);
// nrf_delay_ms(100);
//Write Chip Erase command = 0x60;
m_buffer_tx[0] = 0xC7;//FLASH_CMD_CE;
nrf_drv_spi_transfer(&spi,(uint8_t const *)m_buffer_tx,1,m_buffer_rx,0);
// Chip select go high to end a flash command
nrf_delay_ms(100);
cs_high();
// cmd_rdsr(StatusReg);
// printf("StatusReg= %d \n",StatusReg);
//if( WaitFlashReady( 60000 ) )
nrf_delay_ms(60000);
printf("chip esrsed \n");
return FlashOperationSuccess;
// else
// return FlashTimeOut;
//return FlashOperationSuccess;
}
ReturnMsg full_sector_erase(void)
{
uint8_t i=0;
uint32_t flash_address = FLASH_TARGET_ADDR;
for(i=0;i<5;i++)
{
cmd_se(flash_address);
nrf_delay_ms(240);
flash_address = flash_address + FLASH_SECTORSIZE;
}
}
/*
* Simple flash read/write test
*/
uint8_t flash_read_write_test( void )
{
uint8_t message= 0;
FlashStatus flash_state = {0};
uint32_t flash_addr;
uint32_t trans_len = 0;
uint16_t i=0, error_cnt = 0;
uint16_t seed = 0;
uint8_t st_reg = 0;
/* Assign initial condition */
flash_addr = FLASH_TARGET_ADDR;
trans_len = TRANS_LENGTH;
seed = RANDOM_SEED;
/* Erase 4K sector of flash memory
Note: It needs to erase dirty sector before program */
uint8_t err_code;
// err_code = cmd_se( flash_addr ); //cmd_ce();//cmd_block_erase(flash_addr);//cmd_se( flash_addr );
// printf("error code = %d \n",err_code);
// nrf_delay_ms(300);
//
//
// cmd_read( flash_addr, m_data_receive, TRANS_LENGTH );
// nrf_delay_ms(300);
//
// printf("\r data after chip erase: ");
// for( i=4; i < 20; i++ )
// {
// printf(" %.02x ",m_data_receive[i]);
// nrf_delay_ms(10);
// }
// printf("\n");
//
/* Program data to flash memory */
// cmd_pp( flash_addr, m_data_send,256 ); //TRANS_LENGTH
// nrf_delay_ms(500);
/* Read flash memory data to memory buffer */
// cmd_read( flash_addr, m_data_receive, 256 ); //TRANS_LENGTH
// nrf_delay_ms(300);
/* Compare original data and flash data */
// for( i=4; i < (trans_len); i=i+1 )
// {
// if( m_data_send[i] != m_data_receive[i] )
// {
// printf("wrong data \n");
// Error_inc( error_cnt );
// }
// else
// {
printf("\r data received: ");
for( i=4; i < 256; i++ )
{
printf(" %.02x ",m_data_receive[i]);
nrf_delay_ms(10);
}
printf("\n");
// }
// }
/* Erase 4K sector of flash memory */
// cmd_se( flash_addr ); //cmd_ce();//cmd_block_erase(flash_addr); //
// nrf_delay_ms(240); //240 60000
if( error_cnt != 0 )
return false;
else
return true;
}
uint8_t ext_flash_init(void)
{
uint8_t retval = false;
/* Configure SPI pins */
nrf_drv_spi_config_t spi_config = NRF_DRV_SPI_DEFAULT_CONFIG;
spi_config.ss_pin = SPI_SS_PIN;
spi_config.miso_pin = SPI_MISO_PIN;
spi_config.mosi_pin = SPI_MOSI_PIN;
spi_config.sck_pin = SPI_SCK_PIN;
spi_config.mode = NRF_DRV_SPI_MODE_0;
spi_config.frequency= NRF_DRV_SPI_FREQ_125K;
APP_ERROR_CHECK(nrf_drv_spi_init(&spi, &spi_config, spi_event_handler, NULL));
nrf_gpio_pin_set(SPI_WP_PIN);
// nrf_gpio_pin_clear(SPI_WP_PIN);
uint8_t err_code;
cmd_rsten();
cmd_rst();
err_code = cmd_wrdis();
/* Set CS pin to High*/
// cs_high();
wait_flash_warm_up();
nrf_delay_ms(100);
flash_ID_test(3);
/* read and verify manufacturer and device id from external flash to ensure external flash is working */
if(flash_ID_test(3) == true)
{
// flash_read_write_test();
// return true;
}
// cmd_wren();
// cmd_wrsr(2);
// cmd_rdsr(StatusReg);
// cmd_rdcr(ConfigReg);
//nrf_delay_ms(500);
////cmd_ce();
//// cmd_se(0x000000);
//// nrf_delay_ms(500);
//printf("finish \n");
// cmd_read( 0x000000, m_data_receive, TRANS_LENGTH );
// uint8_t i;
// printf("\r data after chip erase at 0x000000: ");
// for( i=4; i < 20; i++ )
// {
// printf(" %.02x ",m_data_receive[i]);
// nrf_delay_ms(10);
// }
// printf("\n");
// cmd_se(0x008000);
// cmd_read( 0x008000, m_data_receive, TRANS_LENGTH );
//
//
// printf("\r data after chip erase at 0x008000: ");
// for( i=4; i < 20; i++ )
// {
// printf(" %.02x ",m_data_receive[i]);
// nrf_delay_ms(10);
// }
// printf("\n");
return retval;
}
Hi
Thanks. Adding those files I realize that ext_flash.h is also missing ;)
Either way, I will start doing some testing on my own in the mean time, and set up a quick test based on the ble_app_uart example.
Getting 3-4 of the core functions running should not be very time consuming.
Best regards
Torbjørn
Ext_flash.h you can remove it and instead of it add external_flash.h