• State Suggested Answer
  • Replies 12 replies
  • Answers 1 answer
  • Subscribers 70 subscribers
  • Views 4472 views
  • Users 0 members are here
Attachments (0)
Nordic Case Info
  • Case ID: 236498
Options
This post is older than 2 years and might not be relevant anymore
More Info: Consider searching for newer posts

NRF_ERROR_NO_MEM in sd_ble_gatts_characteristic_add

Daniel Reisfeld

Hi,

I get NRF_ERROR_NO_MEM calling sd_ble_gatts_characteristic_add when using more than 15 uuids. Can you help mitigating this?

Thanks,

Daniel

Parents
  • 0

    As the name "NRF_ERROR_NO_MEM" suggests - you've run out of memory!

    You need to increase NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE  in sdk_config.h

    You may then also need to increase RAM_START in the Project Linker settings > Memory placement macros

  • 0 in reply to awneil

    1. What is the relationship (formula) between the number of characteristics and NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE? 

    2. How do I calculate if and by how much I need to increase the RAM_START?

    3. Is there a methodical way to know if the RAM_START is too small?

    Thanks,

    Daniel

  • 0 in reply to Amanda Hsieh

    My 1st question was what is the needed NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE as a function of the number of characteristics; then, which log and finally, how to make sure the RAM_START is correct.

    Thanks,

    Daniel 

  • 0 in reply to Daniel Reisfeld

    Hi Daniel, 

    The attribute table is stored in Softdevice's RAM region (memory layout) and the debug log will ask you to increase the APP_RAM_BASE address if it is set too low for the current configuration, hence allocate more RAM for the Softdevice.

    When you increase the UUID count you need to adjust your ram settings. Otherwise, Error 4 returned by softdevice_enable corresponds to the NRF_ERROR_NO_MEM error. This error is generated by the sd_ble_enable function which is called within softdevice_enable.

    The easiest way of finding the correct RAM settings is by using a terminal such as putty to read the logs supplied by the chip. First make the changes you need to your code (setting the UUID count to what you need), build and load. If the RAM settings are different from the optimal settings the logs displayed in putty will tell you what the RAM start and size should be set to. Then simply change the RAM settings in the target options.

    -Amanda H.

  • 0 in reply to Amanda Hsieh

    Amenda,

    I couldn't find and documentation about the logging functionality of Softdevice. Can you direct me to it?

    Additionally, it seems you suggest a trial and error approach. Isn't there a documentation about the memory requirements based on the number of characteristics? 

    Thanks,

    Daniel

  • 0 in reply to Daniel Reisfeld

    Hi Daniel, 

    If you use S140, you can refer to S140 SoftDevice. 

    NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE indicates the set amount of memory dedicated to the attribute table (including the characteristic size) in the Softdevice, so this will also vary from project to project. If you exceed the size of it you will receive an NRF_ERROR_NO_MEM error. Modifying the NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE usually means you also need to reconfigure the RAM settings.

    For the RAM_START and the RAM_SIZE, there is no need for an equation or optimal values, as the SoftDevice will tell you if you have allocated too little RAM. You can start a debug session with the RTT logging enable if there is insufficient RAM allocated for the SoftDevice the logs will print a warning with the suggested RAM start address. See bjornspockeli's comment here to find out how to output the log information.

    For log information, you could go to sdk_config.h and enable NRF_LOG_ENABLED and NRF_LOG_BACKEND_RTT_ENABLED. Changing NRF_LOG_DEFAULT_LEVEL to 4 could show the "debug" log. 

    -Amanda H.

  • 0 in reply to Amanda Hsieh

    Amenda,

    The logging mechanism in the example you linked to is not of Softdevice. I reiterate my very simple question: What is the relationship (formula) between the number of characteristics and NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE? (I would be happy to get answers also on my other two questions but this is the most important one right now). I don't have the source code for the Softdevice and, therefore, cannot figure out robustly myself.

    Daniel

Reply
  • 0 in reply to Amanda Hsieh

    Amenda,

    The logging mechanism in the example you linked to is not of Softdevice. I reiterate my very simple question: What is the relationship (formula) between the number of characteristics and NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE? (I would be happy to get answers also on my other two questions but this is the most important one right now). I don't have the source code for the Softdevice and, therefore, cannot figure out robustly myself.

    Daniel

Children
Related