NRF52810 initializing TWI (I2C)

[trevortjes]

Hello, I am having problems getting the TWI to work. The NRF52810 needs the TWI to communicate with a EEPROM module.

Thus far ive set:

#include "nrf_drv_twi.h"

#define PIN_SDA	 		25
#define PIN_SCL 		28

/* TWI instance ID. */
#if TWI0_ENABLED
#define TWI_INSTANCE_ID     0
#elif TWI1_ENABLED
#define TWI_INSTANCE_ID     1
#endif

static const nrf_drv_twi_t m_twi = NRF_DRV_TWI_INSTANCE(TWI_INSTANCE_ID);

void InitTWI()
{
	
	const nrf_drv_twi_config_t TWI_CONFIG	=	
	{																 
			.frequency          = NRF_DRV_TWI_FREQ_400K, 																 
			.scl                = PIN_SCL,                                               
			.sda                = PIN_SDA,                                               
			.interrupt_priority = APP_IRQ_PRIORITY_HIGH,                       
			.clear_bus_init     = false	
	};

	nrf_drv_twi_init(&m_twi, &TWI_CONFIG, NULL, NULL);
	nrf_drv_twi_enable(&m_twi);
}

Then I try to do the TWI Scanner example but I get no activity (with scope) on the SCL or SDA line. 

Is there something I forgot?

[Einar Thorsrud]

Hi,

You only initialize the TWI driver in the code snippet in your question. Since there is no code that actually starts a transaction, it is as expected that you don't see any activity on the SCL and SDA lines. You mention the TWI Scanner example, and there you can see that it sets up a read transaction for every address. Using that code (after first initializing as you do), you will see activity on the lines:

    for (address = 1; address <= TWI_ADDRESSES; address++)
    {
        err_code = nrf_drv_twi_rx(&m_twi, address, &sample_data, sizeof(sample_data));
        if (err_code == NRF_SUCCESS)
        {
            detected_device = true;
            NRF_LOG_INFO("TWI device detected at address 0x%x.", address);
        }
        NRF_LOG_FLUSH();
    }

[trevortjes]

This program is added to my project and when debugging it seems like the program gets stuck in a loop of twi_rx_start_transfer and the "hw_timout" part. Any idea what causes this?

Also do I need TWI, TWIM or TWIS when interfacing the NRF52810 with an I2C eeprom IC?

[trevortjes]

Important:

using

  nrf_gpio_pin_toggle(25);
  nrf_gpio_pin_toggle(28);

and turning off the InitTWI() results in both pins toggling from 0V to 3.5V.

[Einar Thorsrud]

Hi,

This is a bit strange. Is this the whole schematic, or are there some relevant parts missing? Have you tried with an nRF dev kit (instead of your custom HW) and external pullups? If not, can you try that? What happens if you test with another I2C slave device instead?

[trevortjes]

This is everything to the hardware besides some ESD protection.

I only have access to the nRF51822-DK. Is it true that I have to set the GPIO configuration for the SCL and SDA pins myself, or does the TWI library do this when telling it what the SCL and SDA pins are.

I will try now to remove the ESD protection and see if anything changes. I will also turn on the internal pullups without interference of the TWI related stuff and see if the odd pin levels remain.

[Einar Thorsrud]

Hi,

The GPIO's are configured by the driver with pullups, so there is no need to explicitly configure them before. There were some issues here (missing pull-up configuration) some SDK released back (you can see this from the driver implementation). Which SDK version do you use?

[trevortjes]

Turns out it was indeed a hardware error. The ESD protection was influencing the TWI lines. Already succesfully wrote and read data from the EEPROM module.