This post is older than 2 years and might not be relevant anymore
More Info: Consider searching for newer posts

RTE\Device\nRF52832_xxAA\system_nrf52.c(29): error: #5: cannot open source input file "nrf_erratas.h": No such file or directory

I am using nRF52832, And SDK 15.3, the ble_app_blinky project,

a. if i have installed only the latest version of Device family 8.29.0 , when i try to build the project, it asks for permission to install 8.24.1 also.as shown in below fig

b. If I install version 8.24.1 in the pack installer as shown below, I get an error with erratas.h file

I have tried the solution given in other thread, to delete a file in module folder. But the error still persists.

Can anyone kindly guide me?

Top Replies

Chuang over 4 years ago +5 verified

It's a bug of MDK-ARM. MDK always copies `system_nrf52.c` from the latest software pack (currently 8.29.0), even though you selected the old version that SDK 15.3 supports (8.17.0). My solution is…

Parents

0 Simonr over 4 years ago

Hi

I found the nrf_erratas.h file, and it seems it is located in the path \Keil_v5\ARM\PACK\NordicSemiconductor\nRF_DeviceFamilyPack\8.29.0\Device\Include. Sorry to have misled you. Seems like there's an error with MDK version 8.29.0 where this file isn't included in the projects by itself. Please try adding it manually.

Best regards,

Simon
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Nats over 4 years ago in reply to Simonr

Can you please tell me, where i can find this file? Whats the procedure to manually include?

Because i dont find it in the SDK folder
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Simonr over 4 years ago in reply to Nats

I found the file at C:\Keil_v5\ARM\PACK\NordicSemiconductor\nRF_DeviceFamilyPack\8.29.0\Device\Include. Please check wherever you downloaded Keil on your computer. In Keil uVision you set the include path from Project -> Options for Target ... -> C/C++. There, in the lower half of the window, you can modify the Include Paths.

Best regards,

Simon
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Nats over 4 years ago in reply to Simonr

The path you are mentioning doesnt exist in my drive

...I included both the paths, and im still facing the error with erratas.h file.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 wlping_ing over 4 years ago in reply to Nats

it is not exactly the same path as Simonr described, but you can search nRF_DeviceFamilyPack\8.29.0\Device\Include, i do find that file in pack, but need to modify .h a little bit;

my path is under ”C:\Users\user\AppData\Local\Arm\Packs“
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Reply

0 wlping_ing over 4 years ago in reply to Nats

it is not exactly the same path as Simonr described, but you can search nRF_DeviceFamilyPack\8.29.0\Device\Include, i do find that file in pack, but need to modify .h a little bit;

my path is under ”C:\Users\user\AppData\Local\Arm\Packs“
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Children

0 TomSt over 4 years ago in reply to wlping_ing

Hi,

I had exactly the same problem but finally I've sorted this issue:

1. Remove nRF_DeviceFamilyPack version 8.29 because it looks like automatically add to system_nrf_528xx #include "nrf_erratas.h" which makes a problem.

I am using 8.24.1

2. Close Keil

2. Unzip once again the SDK and open blinky project (just to clear)

3. Compile and should work.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Nats over 4 years ago in reply to wlping_ing

Including that file, throws another error
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Nats over 4 years ago in reply to TomSt

Hey, Thank you so much. This helped
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

0 Nats over 4 years ago in reply to Nats

i have uploaded sdk 15 BLE blinky example, s132 soft device

The nrf connect reads as below,

2019-11-11T07:50:18.248Z INFO Application data folder: C:\Users\bjnag\AppData\Roaming\nrfconnect\pc-nrfconnect-programmer
2019-11-11T07:50:19.780Z DEBUG App pc-nrfconnect-programmer v1.2.3 official
2019-11-11T07:50:19.781Z DEBUG App path: C:\Users\bjnag\.nrfconnect-apps\node_modules\pc-nrfconnect-programmer
2019-11-11T07:50:19.781Z DEBUG nRFConnect 3.2.0 is supported by the app (^3.2.0)
2019-11-11T07:50:19.781Z DEBUG nRFConnect path: C:\Users\bjnag\AppData\Local\Programs\nrfconnect\resources\app.asar
2019-11-11T07:50:19.782Z DEBUG HomeDir: C:\Users\bjnag
2019-11-11T07:50:19.782Z DEBUG TmpDir: C:\Users\bjnag\AppData\Local\Temp
2019-11-11T07:50:19.847Z INFO Using nrfjprog library 10.3.0, pc-nrfjprog-js 1.5.8
2019-11-11T07:50:28.933Z INFO Using nrfjprog to communicate with target
2019-11-11T07:51:22.259Z INFO Target device closed.
2019-11-11T07:51:24.473Z INFO Using nrfjprog to communicate with target
2019-11-11T07:51:26.998Z INFO Using J-Link Software version 6.50
2019-11-11T07:51:32.641Z INFO Segger serial:  519001316
2019-11-11T07:51:32.642Z INFO Segger speed:  2000  kHz
2019-11-11T07:51:32.643Z INFO Segger version:  J-Link Lite-Cortex-M V9 compiled May 17 2019 09:50:01
2019-11-11T07:51:32.683Z INFO Probed: 519001316.
2019-11-11T07:51:32.684Z INFO Model: NRF52832_xxAA_REV1.
2019-11-11T07:51:32.685Z INFO RAM: 64KiB.
2019-11-11T07:51:32.685Z INFO Flash: 512KiB in pages of 4KiB.
2019-11-11T07:51:36.112Z INFO Reading device non-volatile memory. This may take a few seconds.
2019-11-11T07:51:41.098Z INFO Non-volatile memory has been read. 5 non-empty memory blocks identified.
2019-11-11T07:51:41.259Z INFO SoftDevice detected, id 0x81 (S132 v2.0.0)
2019-11-11T07:53:32.606Z INFO Using nrfjprog to communicate with target
2019-11-11T07:53:35.425Z INFO Using J-Link Software version 6.50
2019-11-11T07:53:38.350Z INFO Segger serial:  519001316
2019-11-11T07:53:38.351Z INFO Segger speed:  2000  kHz
2019-11-11T07:53:38.351Z INFO Segger version:  J-Link Lite-Cortex-M V9 compiled May 17 2019 09:50:01
2019-11-11T07:53:38.370Z INFO Probed: 519001316.
2019-11-11T07:53:38.371Z INFO Model: NRF52832_xxAA_REV1.
2019-11-11T07:53:38.371Z INFO RAM: 64KiB.
2019-11-11T07:53:38.371Z INFO Flash: 512KiB in pages of 4KiB.
2019-11-11T07:53:40.198Z INFO Reading device non-volatile memory. This may take a few seconds.
2019-11-11T07:53:44.902Z INFO Non-volatile memory has been read. 6 non-empty memory blocks identified.
2019-11-11T07:53:45.102Z INFO SoftDevice detected, id 0x81 (S132 v2.0.0)
2019-11-11T07:54:01.696Z INFO Recovery procedure finished
2019-11-11T07:54:01.711Z INFO Using nrfjprog to communicate with target
2019-11-11T07:54:03.836Z INFO Using J-Link Software version 6.50
2019-11-11T07:54:06.367Z INFO Segger serial:  519001316
2019-11-11T07:54:06.367Z INFO Segger speed:  2000  kHz
2019-11-11T07:54:06.367Z INFO Segger version:  J-Link Lite-Cortex-M V9 compiled May 17 2019 09:50:01
2019-11-11T07:54:06.385Z INFO Probed: 519001316.
2019-11-11T07:54:06.386Z INFO Model: NRF52832_xxAA_REV1.
2019-11-11T07:54:06.386Z INFO RAM: 64KiB.
2019-11-11T07:54:06.386Z INFO Flash: 512KiB in pages of 4KiB.
2019-11-11T07:54:08.501Z INFO Reading device non-volatile memory. This may take a few seconds.
2019-11-11T07:54:13.145Z INFO Non-volatile memory has been read. 1 non-empty memory blocks identified.
2019-11-11T07:54:15.223Z INFO Parsing HEX file:  C:\Users\bjnag\Desktop\Softwares\s132_nrf52_7.0.1_softdevice.hex
2019-11-11T07:54:15.435Z INFO File was last modified at  8/29/2019, 10:57:45 AM
2019-11-11T07:54:15.600Z INFO Data block: 0x00000000-0x00000B00 (0x00000B00  bytes long)
2019-11-11T07:54:15.601Z INFO Data block: 0x00001000-0x000258C0 (0x000248C0  bytes long)
2019-11-11T07:54:15.603Z INFO SoftDevice detected, id 0xCB (S132 v7.0.1)
2019-11-11T07:54:22.910Z INFO Writing procedure starts
2019-11-11T07:54:32.305Z INFO Write procedure finished
2019-11-11T07:54:32.311Z INFO Using nrfjprog to communicate with target
2019-11-11T07:54:34.588Z INFO Using J-Link Software version 6.50
2019-11-11T07:54:37.345Z INFO Segger serial:  519001316
2019-11-11T07:54:37.346Z INFO Segger speed:  2000  kHz
2019-11-11T07:54:37.346Z INFO Segger version:  J-Link Lite-Cortex-M V9 compiled May 17 2019 09:50:01
2019-11-11T07:54:37.368Z INFO Probed: 519001316.
2019-11-11T07:54:37.369Z INFO Model: NRF52832_xxAA_REV1.
2019-11-11T07:54:37.369Z INFO RAM: 64KiB.
2019-11-11T07:54:37.369Z INFO Flash: 512KiB in pages of 4KiB.
2019-11-11T07:54:39.286Z INFO Reading device non-volatile memory. This may take a few seconds.
2019-11-11T07:54:44.197Z INFO Non-volatile memory has been read. 3 non-empty memory blocks identified.
2019-11-11T07:54:44.334Z INFO SoftDevice detected, id 0xCB (S132 v7.0.1)
2019-11-11T07:54:44.336Z INFO SoftDevice detected, id 0xCB (S132 v7.0.1)
2019-11-11T07:54:54.820Z INFO Using nrfjprog to communicate with target
2019-11-11T07:54:57.112Z INFO Using J-Link Software version 6.50
2019-11-11T07:54:59.873Z INFO Segger serial:  519001316
2019-11-11T07:54:59.873Z INFO Segger speed:  2000  kHz
2019-11-11T07:54:59.873Z INFO Segger version:  J-Link Lite-Cortex-M V9 compiled May 17 2019 09:50:01
2019-11-11T07:54:59.893Z INFO Probed: 519001316.
2019-11-11T07:54:59.894Z INFO Model: NRF52832_xxAA_REV1.
2019-11-11T07:54:59.894Z INFO RAM: 64KiB.
2019-11-11T07:54:59.896Z INFO Flash: 512KiB in pages of 4KiB.
2019-11-11T07:55:02.055Z INFO Reading device non-volatile memory. This may take a few seconds.
2019-11-11T07:55:06.762Z INFO Non-volatile memory has been read. 4 non-empty memory blocks identified.
2019-11-11T07:55:06.899Z INFO SoftDevice detected, id 0xCB (S132 v7.0.1)
2019-11-11T07:55:06.901Z INFO SoftDevice detected, id 0xCB (S132 v7.0.1)

But, when i open BLE of nRF COnnect, i get the following error
08:55:11.147 Application data folder: C:\Users\bjnag\AppData\Roaming\nrfconnect\pc-nrfconnect-ble 08:55:15.499 Validating connectivity firmware for device with serial number 000519001316... 08:55:18.629 Error while setting up device 000519001316: No serial port available for device with serial number 000519001316 08:55:18.636 Device closed. 08:55:57.585 Validating connectivity firmware for device with serial number 000519001316... 08:55:59.726 Error while setting up device 000519001316: No serial port available for device with serial number 000519001316 08:55:59.730 Device closed. 09:02:04.763 Validating connectivity firmware for device with serial number 000519001316... 09:02:07.461 Error while setting up device 000519001316: No serial port available for device with serial number 000519001316 09:02:07.467 Device closed.

ANd i cant view the device in App either

0 TomSt over 4 years ago in reply to Nats

Hi,

Problem is not related to the previous one. Something silly with com port.

If you use win10 try to go to the device manager and disable this specific com port and enable it once again. then restart nrf connect and try.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel