Cannot write/read a byte from external Flash via SPI

[RO]

I am using a BMD 349 module based on nRF52840. 

I am interfacing with AT25SF041 flash memory.

I am using SDK 14.2.

I am writing a byte to a specific address in Flash. 

But when I try to read the memory location, On the debug window I only see "00". 

I don't see any error messages.

I can read the status registers and Device ID completely fine, so I know SPI read function is working.

Can someone help?

Thanks

Below is flash_mem.c 

#include "flash_mem.h"
#include "nrf_drv_spi.h"
#include "nrf_gpio.h"

static const nrf_drv_spi_t m_spi_at = NRF_DRV_SPI_INSTANCE(0);

static uint32_t spi_config(void)
{
    uint32_t err_code;
    nrf_drv_spi_config_t config = NRF_DRV_SPI_DEFAULT_CONFIG;
    config.frequency = NRF_DRV_SPI_FREQ_1M;
    config.mode      = NRF_DRV_SPI_MODE_3;
    config.bit_order = NRF_DRV_SPI_BIT_ORDER_MSB_FIRST;
    config.mosi_pin  = AT_PIN_MOSI;
    config.miso_pin  = AT_PIN_MISO;
    config.sck_pin   = AT_PIN_SCK;
    config.ss_pin    = AT_PIN_CS; 
    err_code = nrf_drv_spi_init(&m_spi_at, &config, NULL, NULL);
    if (err_code != NRF_SUCCESS)
    {
        // Initialization failed. Take recovery action.
    }   
    nrf_gpio_cfg_output(AT_PIN_CS);
    nrf_gpio_pin_set(AT_PIN_CS);
    return err_code;
}


uint32_t at_init(void)
{
    return spi_config();
}

void at_read_rems(uint8_t * manufacturer_id, uint8_t * device_id)
{
    uint8_t spi_tx_cmd[] = {0x9F};
    uint8_t spi_rx_response[3];
    nrf_gpio_pin_clear(AT_PIN_CS);
    nrf_drv_spi_transfer(&m_spi_at, spi_tx_cmd, sizeof(spi_tx_cmd), spi_rx_response, sizeof(spi_rx_response));
    nrf_gpio_pin_set(AT_PIN_CS);
    *manufacturer_id = spi_rx_response[1]; 
    *device_id = spi_rx_response[2];
}


void at_write_enable(void)
{
    static uint8_t spi_tx_cmd[] = {CMD_WREN};
    nrf_gpio_pin_clear(AT_PIN_CS);
    nrf_drv_spi_transfer(&m_spi_at, spi_tx_cmd, sizeof(spi_tx_cmd), 0, 0);
    nrf_gpio_pin_set(AT_PIN_CS);
}

void at_program(uint32_t address, uint8_t * data_ptr, uint32_t data_length)
{
    uint8_t spi_tx_cmd[] = {CMD_PROGRAM, (address >> 16) & 0xFF, (address >> 8) & 0xFF, (address >> 0) & 0xFF};
    nrf_gpio_pin_clear(AT_PIN_CS);
    nrf_drv_spi_transfer(&m_spi_at, spi_tx_cmd, sizeof(spi_tx_cmd),NULL, NULL);
    while(data_length > 255)
    {
        nrf_drv_spi_transfer(&m_spi_at, data_ptr, 255, NULL, NULL);
        data_ptr += 255;
        data_length -= 255;
    }
    nrf_drv_spi_transfer(&m_spi_at, data_ptr, data_length, NULL, NULL);
    nrf_gpio_pin_set(AT_PIN_CS);
}


void at_read(uint32_t address, uint8_t * data_ptr, uint32_t data_length)
{
    uint8_t spi_tx_cmd[] = {CMD_READ, (address >> 16) & 0xFF, (address >> 8) & 0xFF, (address >> 0) & 0xFF};
    nrf_gpio_pin_clear(AT_PIN_CS);
    nrf_drv_spi_transfer(&m_spi_at, spi_tx_cmd, sizeof(spi_tx_cmd), NULL, NULL);
    while(data_length > 255)
    {
        nrf_drv_spi_transfer(&m_spi_at, 0, 0, data_ptr, 255);
        data_ptr += 255;
        data_length -= 255;
    }
    nrf_drv_spi_transfer(&m_spi_at, NULL, NULL , data_ptr, data_length);
    nrf_gpio_pin_set(AT_PIN_CS);
}

Below is part of main.c

int main(void)
{

    uint8_t status_register, man_id, dev_id;
    uint8_t data_buf = 0x23;
    uint8_t read_buf;
    at_init();
    at_write_enable();

    uint32_t address = 0x01A8FF;
            //for(int i = 0; i < READ_WRITE_LENGTH; i++) data_buf[i] = i;
            at_program(address, &data_buf, 1);
            
        at_read(address, &read_buf, 1);
       NRF_LOG_INFO("Reading address %.8x: ", address);
       NRF_LOG_INFO("%.2X-" ,(int)read_buf);
}

[Turbo J]

RO said:

I am writing a byte to a specific address in Flash. 

But when I try to read the memory location, On the debug window I only see "00". 

You can only write "0" bits to flash.

Returning to "1" is the "erase" operation, which has its own command (and operates on a page or sector at a time).

[RO]

Sorry I dont understand,

as wriiten in the code, I'm trying to write "0x23" to a specific memory location.

I want to read "0x23" back, am I doing something wrong?

Thanks

[Edvin]

Turbo J is correct. An erased byte is 0xFF, so if you are reading 0x00, that means that something else has already written to that address. Try to read it before you write to it.

So what you probably need to do is to find the SPI command to erase everything on the flash (or that specific flash page). 

Best regards,

Edvin

[RO]

I did the following:

write enable -> chip erase -> read (random address)

I still read 00. Shouldn't I read FF after a chip erase?

I added delays for each operation as per datasheet. 

I can read status registers fine. Why am I not able read data in random address' correctly?

Thanks

[Edvin]

I don't know what external flash you use. You should check in the data sheet for the flash. Have you tried analyzing the SPI wires to see that the data that you are sending and receiving is actually being sent correctly? Have you tried lowering the SPI frequency? Perhaps the traces/wires are too long for 1M? Perhaps you are using the wrong config.mode?

[RO]

I don't have access to a logic analyzer yet. The fact that I can read manufacturer and device ID over SPI, doesn't that prove that SPI connection has been correctly established?
I tried with 500k frequency, and the config mode is correct too. For some reason I'm only reading zeros..