Current consumption when using rtc, ppi and gpiote

[stanley_c]

Hi Sir/Madam

I wrote a small program for low current verification on nrf51822 development kit with starter mother board. The program is based on "blinky_example" project configuration. It is doing gpio pin 24 toggling by using rtc, ppi and gpiote modules. However, the voltage reading from connector K2 is about 120mV or 1200uA at P7 even the CPU is called "__WFI" and unplugged the Jlink. From my understanding, CPU can operate below 5uA when it is sleep. Or ppi module is already used 1mA? Or something wrong on the code. Thanks a lot.

#define LFCLK_FREQUENCY          (32768UL)             /*!< LFCLK frequency in Hertz, constant */
#define RTC_FREQUENCY             (8UL)                     /*!< required RTC working clock RTC_FREQUENCY Hertz. Changable */
#define COMPARE_COUNTERTIME       (1UL)            /*!< Get Compare event COMPARE_TIME seconds after the counter starts from 0 */

#define COUNTER_PRESCALER         ((LFCLK_FREQUENCY/RTC_FREQUENCY) - 1)  /* f = LFCLK/(prescaler + 1) */


void ppi_init(void)
{
	// Configure PPI channel 0 to start ADC task	
	NRF_PPI->CH[0].EEP = (uint32_t)&NRF_RTC0->EVENTS_TICK;	
	NRF_PPI->CH[0].TEP = (uint32_t)&NRF_GPIOTE->TASKS_OUT[0];

	// Enable PPI channel 0
	NRF_PPI->CHEN = (PPI_CHEN_CH0_Enabled << PPI_CHEN_CH0_Pos);
}

static void rtc_config(void)
{
	NRF_RTC0->PRESCALER = COUNTER_PRESCALER;                   // Set prescaler to a TICK of RTC_FREQUENCY
	
	// Enable TICK event and TICK interrupt:
	NRF_RTC0->EVTENSET = RTC_EVTENSET_TICK_Msk;
}

static void lfclk_config(void)
{
	NRF_CLOCK->LFCLKSRC = (CLOCK_LFCLKSRC_SRC_Xtal << CLOCK_LFCLKSRC_SRC_Pos);
	NRF_CLOCK->EVENTS_LFCLKSTARTED = 0;
	NRF_CLOCK->TASKS_LFCLKSTART = 1;
	while (NRF_CLOCK->EVENTS_LFCLKSTARTED == 0)
	{
	}
	NRF_CLOCK->EVENTS_LFCLKSTARTED = 0;
}

/**
 * main() function
 * @return 0. int return type required by ANSI/ISO standard.
 */
int main(void)
{
	nrf_gpio_cfg_output(24);
	lfclk_config();
	rtc_config();

	ppi_init();
       
        // Configure the GPIOTE Task to toggle the LED state.
    nrf_gpiote_task_config(0,                         
						   24,
                           NRF_GPIOTE_POLARITY_TOGGLE,						   
                           NRF_GPIOTE_INITIAL_VALUE_LOW);

	
	NRF_RTC0->TASKS_START = 1;
	
    // Enter main loop
    for ( ; ; )
    {		
		__WFI();
	}	
}

[Erland Lewin]

I asked about this too, but have not received a reply from Nordic Semi. See: devzone.nordicsemi.com/.../power-use-with-gpiote-is-too-high

My impressions is that there may be a hardware bug causing the CPU not to go to sleep properly when using GPIOTE. Even my minimal program with only one line of code that only enables GPIOTE causes too high current use:

	NRF_GPIOTE->CONFIG[GPIOTE_CHANNEL_NUMBER] = 
(GPIOTE_CONFIG_MODE_Task *shiftleft* GPIOTE_CONFIG_MODE_Pos)     |
                                         ((uint32_t)outPin *shiftleft* GPIOTE_CONFIG_PSEL_Pos)     |
                                         ((uint32_t)NRF_GPIOTE_POLARITY_TOGGLE *shiftleft* GPIOTE_CONFIG_POLARITY_Pos) |
                                         ((uint32_t)NRF_GPIOTE_INITIAL_VALUE_HIGH *shiftleft* GPIOTE_CONFIG_OUTINIT_Pos);

Please Nordic Semi, can you confirm this problem, and hopefully give a work-around!

[stanley_c]

Thanks for your information. I re-check my code, as u said the current seems drawn from gpiote "nrf_gpiote_task_config". However, the current consumption of gpiote block is 0.1uA in output mode and 100uA even it's in in input mode. (nRF51822 Product Specification v1.3 section 8.10 GPIOTE specifications).