CONFIG_LOG at runtime

[anicare-tero]

Hi,

Is it possible to disable logger at runtime on nRF9160? I would like to have a logger at device's first startup after flashing (like in production test mode) and then disable the logger when exiting from that test mode and then rebooting and going to the normal device mode. How should I do that or is it even possible?

Could I set CONFIG_LOG to false or am I even able to change configs at runtime?

Regards,
Tero

[Hadrien Kohl]

It is, you can turn this option on in your KConfig.

https://docs.zephyrproject.org/latest/reference/kconfig/CONFIG_LOG_RUNTIME_FILTERING.html#cmdoption-arg-config-log-runtime-filtering

You can then use log_filter_set to change the log level. 

docs.zephyrproject.org/.../index.html

[anicare-tero]

Hi Hadrien, thanks for your reply!

I read that earlier and thought I have to test that at some point. But now because you confirmed that it's working, I will test that soon.

[Einar Thorsrud]

Hi,

anicare-tero said:

We need logger for production testing but not anymore after exiting the test mode.

Do you need disconnect the programmer for production testing? If not, could you not re-program firmware without logging after running the tests that require logging?

anicare-tero said:

Or then I should disable logger compile-time and use other way, like add printk() to every place that will be needed in testing.

That may be the best solution in this case. You could still use the log system for another testing during development, but not for logging you need for production testing.

[anicare-tero]

Einar Thorsrud said:

Do you need disconnect the programmer for production testing? If not, could you not re-program firmware without logging after running the tests that require logging?

I can't re-program a firmware because I have to disable UART also in normal mode. And then if I have to flash a normal firmware without UART, I'm not able to write serialnumber and some other stuff to NVS. Or is it possible to flash another firmware without erasing the NVS?

[Einar Thorsrud]

Hi,

anicare-tero said:

And then if I have to flash a normal firmware without UART, I'm not able to write serialnumber and some other stuff to NVS.

Why can you not write the serial number etc. via SWD?

anicare-tero said:

Or is it possible to flash another firmware without erasing the NVS?

That is no problem. You can do a sector erase instead of a full chip erase. The only requirement is that the data you want to preserve is not on the same page as the application itself since you can only erase full pages.

[anicare-tero]

Hi,

Einar Thorsrud said:

Why can you not write the serial number etc. via SWD?

How should I do that? We had a little conversation about storing a device serial identifier with phipi in https://devzone.nordicsemi.com/f/nordic-q-a/51462/storing-device-serial-identifier .

Einar Thorsrud said:

That is no problem. You can do a sector erase instead of a full chip erase. The only requirement is that the data you want to preserve is not on the same page as the application itself since you can only erase full pages.

Is there any examples or tutorials how to do a sector erase? I can't use nRF Connect for Desktop's Programmer for this, right? Should a sector erase be done from command line?

[Einar Thorsrud]

Hi,

anicare-tero said:

How should I do that? We had a little conversation about storing a device serial identifier with phipi in https://devzone.nordicsemi.com/f/nordic-q-a/51462/storing-device-serial-identifier .

It is of course up to you. I would consider putting it in the OTP registers in UICR.

anicare-tero said:

Is there any examples or tutorials how to do a sector erase? I can't use nRF Connect for Desktop's Programmer for this, right? Should a sector erase be done from command line?

You can program using nrfjprog, just add --sectorerase to the command when you program. Something like this:

nrfjprog -f nrf91 --program app.hex --sectorerase