Clarification about SPIM - SS pin management for nrf9160

Question

Hello, 
 i'm trying to understand how the management of the SS pin is (or has to be) performed when using nrf9160 as SPI master. 
 In this post Håkon said that: 
 "Most driver implementations has its own property for SS pin, as this is essentially a GPIO output that is set/cleared (SPIM doesn't have a dedicated hardware CSN/SS pin). The nrfx_spim driver itself supports handling the SS pin, but this is disabled for the zephyr SPI port layer: https://github.com/NordicPlayground/fw-nrfconnect-zephyr/blob/master/drivers/spi/spi_nrfx_spim.c#L411 " " 
 So i have to implement my own SS-pin management and that's generally fine. It's here that i become confused. In the SPI API provided is defined this: 
 struct spi_config {
	u32_t frequency;
	u16_t operation;
	u16_t slave;

	const struct spi_cs_control *cs;
}; 
 where: 
 struct spi_cs_control {
	struct device	*gpio_dev;
	u32_t gpio_pin;
	u32_t delay;
}; 
 Have the struct elements "operation" (it has cs_active_high option) and "spi_cs_control" have any effect on the behaviour of the ss-pin? Does it effectively pull the pin high/low? Or i can leave these struct empty because this part is disabled? 
 
 In the case these struct elements are ineffective, i suppose this is the summarized way to proceed: 
 //NOT REAL CODE, JUST TO SUMMARIZE OPERATIONS
 
 void spi_dev_write(spi_dev, spi_cfg, gpio_ss_dev, ss_pin, ) {
 gpio_pin_write(gpio_ss_dev, ss_pin, 0); //PULL CS LOW
 err = spi_write(spi_dev, spi_cfg, const struct spi_buf_set tx); //WRITE
 gpio_pin_write(gpio_ss_dev, ss_pin, 1); //PULL CS HIGH
 } 
 Am i correct? 
 
 Thanks, 
 frax

Kenneth · Accepted Answer

I was thinking the CS logic was handled in hardware, but by experimenting with it I can see it's handled in software by the driver. So it is possible to use the CS logic in the driver, I made an example below. Best regards, Kenneth Fullscreen main.c Download #include #include #include #include LOG_MODULE_REGISTER(main, LOG_LEVEL_INF); #define GPIO_DRV_PORT DT_NORDIC_NRF_GPIO_GPIO_0_LABEL #define CSN_PIN DT_GPIO_LEDS_LED_0_GPIOS_PIN #define SPI_DRV_NAME DT_NORDIC_NRF_SPI_SPI_1_LABEL #define BUF_SIZE 12 u8_t buffer_tx[BUF_SIZE] = "Hello World"; u8_t buffer_rx[BUF_SIZE]; struct device *spi_dev; struct device *gpio_dev; struct spi_cs_control cs_cfg = { .gpio_dev = NULL, .gpio_pin = CSN_PIN, .delay = 100, }; const struct spi_config spi_cfg_slow = { .frequency = 1000000, .operation = SPI_OP_MODE_MASTER | SPI_WORD_SET(8) | SPI_LINES_SINGLE, .slave = 0, .cs = &cs_cfg, }; const struct spi_buf tx_bufs[] = { { .buf = buffer_tx, .len = BUF_SIZE, }, }; const struct spi_buf rx_bufs[] = { { .buf = buffer_rx, .len = BUF_SIZE, }, }; const struct spi_buf_set tx = { .buffers = tx_bufs, .count = ARRAY_SIZE(tx_bufs) }; const struct spi_buf_set rx = { .buffers = rx_bufs, .count = ARRAY_SIZE(rx_bufs) }; void main(void) { int ret; gpio_dev = device_get_binding(GPIO_DRV_PORT); if (!gpio_dev) { LOG_INF("gpio port was not found %s! ", GPIO_DRV_PORT); return; } LOG_INF("gpio port initialized"); spi_dev = device_get_binding(SPI_DRV_NAME); if (!spi_dev) { LOG_ERR("spi was not found %s! ", SPI_DRV_NAME); return; } LOG_INF("spi initialized"); cs_cfg.gpio_dev = gpio_dev; while(1) { //gpio_pin_configure(gpio_dev, CSN_PIN,0); //gpio_pin_write(gpio_dev, CSN_PIN, 0); ret = spi_transceive(spi_dev, &spi_cfg_slow, &tx, &rx); //gpio_pin_write(gpio_dev, CSN_PIN, 1); LOG_HEXDUMP_INF(&rx, sizeof(rx), "received"); k_sleep(1000); } }

Clarification about SPIM - SS pin management for nrf9160

Top Replies