Cannot get button/gpio interrupt on NET CPU using nRF5340DK

[jyi]

Using just the nRF Connect SDK, I cannot get a push button to interrupt the NET CPU on the nRF5340DK.

I have the following code on the APP CPU:

  nrf_gpio_pin_mcu_select(23, NRF_GPIO_PIN_MCUSEL_NETWORK);

The following code runs on the NET CPU:

  nrfx_gpiote_init(NRFX_GPIOTE_DEFAULT_CONFIG_IRQ_PRIORITY);
  nrfx_gpiote_in_config_t cfg = NRFX_GPIOTE_CONFIG_IN_SENSE_TOGGLE(false);
  cfg.pull = NRF_GPIO_PIN_PULLUP;
  nrfx_gpiote_in_init(NRF_GPIO_PIN_MAP(0, 23), &cfg, MyEventHandler);
  nrfx_gpiote_in_event_enable(NRF_GPIO_PIN_MAP(0, 23), true);

Please help identify what I'm missing. Thank you in advance!

[jyi]

Sigurd,

Thanks for the response. However, I believe my code is already doing what you suggested. Unless I'm missing something, can you please elaborate?

John

[Sigurd]

Hi,

Did you connect GPIOTE_0 IRQ to nrfx_gpiote_irq_handler ?

You could take a look at how it's done in the Zephyr nrfx sample. See this link. To test this sample, build the nrfx sample for the nrf5340pdk_nrf5340_cpunet. And for the app core, you could e.g. use the NCS empty_app_core sample, and build that for nrf5340pdk_nrf5340_cpuapp. See this link.

[jyi]

Ahh...I missed this. I have this connected now but still do not get an interrupt.

I verified pin configuration is correct by using nrf_gpio_pin_read(23). I can see the return value is the correct button state. This confirms the NET CPU is in control of the pin.

Now it is just a matter of getting a NET CPU interrupt on button toggle. These are the registers I verified after button push (looks correct):

INTENSET (0x4100A304) = 0x8000000f
EVENTS_IN[0] (0x4100A100) = 0x1
EVENTS_IN[1] (0x4100A104) = 0x1
EVENTS_IN[2] (0x4100A108) = 0x1
EVENTS_IN[3] (0x4100A10C) = 0x1

As for connecting ISR handlers, I confirmed the vector table is setup in this manner:

SCB->VTOR = IrqVectors[]
IrqVectors[26] =nrfx_gpiote_irq_handler  // 26: GPIOTE_IRQn
NVIC_EnableIRQ(GPIOTE_IRQn);

Global interrupts are enabled. Any thing else I should check?

[Sigurd]

The following works fine here, testing on NCS v1.3.0 on a PCA10095 version 0.7.0

For nrf5340pdk_nrf5340_cpuapp, I'm running the empty_app_core sample.

On nrf5340pdk_nrf5340_cpunet, I'm running this:

main.c

/*
 * Copyright (c) 2019 Nordic Semiconductor ASA
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include <zephyr.h>

#include <nrfx_gpiote.h>

#include <logging/log.h>
LOG_MODULE_REGISTER(nrfx_sample, LOG_LEVEL_INF);

static void button_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
	LOG_INF("GPIO input event callback");
}

void main(void)
{
	LOG_INF("nrfx_gpiote sample on %s", CONFIG_BOARD);

	/* Connect GPIOTE_0 IRQ to nrfx_gpiote_irq_handler */
	IRQ_CONNECT(DT_IRQN(DT_NODELABEL(gpiote)),
		    DT_IRQ(DT_NODELABEL(gpiote), priority),
		    nrfx_isr, nrfx_gpiote_irq_handler, 0);


    nrfx_gpiote_init(NRFX_GPIOTE_DEFAULT_CONFIG_IRQ_PRIORITY);
    nrfx_gpiote_in_config_t cfg = NRFX_GPIOTE_CONFIG_IN_SENSE_TOGGLE(false);
    cfg.pull = NRF_GPIO_PIN_PULLUP;
    nrfx_gpiote_in_init(NRF_GPIO_PIN_MAP(0, 23), &cfg, button_handler);
    nrfx_gpiote_in_event_enable(NRF_GPIO_PIN_MAP(0, 23), true);
  
}

prj.conf

CONFIG_GPIO=n
CONFIG_NRFX_GPIOTE=y
CONFIG_LOG=y
CONFIG_LOG_PROCESS_THREAD_SLEEP_MS=100

Then when I press button 1 (pin 23) on the kit, I get "GPIO input event callback" printed in the terminal (see this link on how to get log-output).

[jyi]

Sigurd,

Thank you for trying this and confirming the code works. The difference in my setup is that I'm not using zephyr. 

I did try using the empty_app_core on the APP CPU. And I tried using your NET CPU example code (removing the zephyr code) and I'm still not getting interrupts.

My issue must have something to do with the code prior to main(). I will keep trying to see if I can resolve. But if you can point me to the zephyr startup code (e.g. Reset Handler) and/or if the ncs has a non-zephyr startup example, that would help.

Appreciate your effort to help me on this issue.

Thanks.

John

[Sigurd]

If you set a breakpoint in nrfx_gpiote_irq_handler(), and press the button, do you hit the breakpoint ?

If not, make sure that you have something like this defined,

// GPIOTE0_IRQn
#define nrfx_gpiote_irq_handler     GPIOTE_IRQHandler

Still not working, then you might need something like this,

#define NRF_GPIOTE        NRF_GPIOTE0
#define GPIOTE_IRQHandler GPIOTE0_IRQHandler