Transmitting data over UART_2 to external sensors

[Adeel]

Hi Dev Team,

I have been trying to send data across from my nRF9160DK board to an external sensor via RS-485. For this, I have a TTL_RS485 converter in between.

To start off with, I just want to send a string and receive it on an external debugger to check my UART communication. I am using UART_2 and I am attaching my nrf9160dk_nrf9160ns.overlay file here. The wiring has been done based on uart_2 configuration. 

/* Needed to get NRF_PWMn defined. */


/ {
	model = "Nordic nRF9160 DK NRF9160";
	compatible = "nordic,nrf9160-dk-nrf9160";

	chosen {
		zephyr,console = &uart0;
		zephyr,shell-uart = &uart0;
		zephyr,uart-mcumgr = &uart0;
	};
};


&pwm1 {
	status = "okay";
};

&pwm2 {
	status = "okay";
};

&pwm3 {
	status = "okay";
};


&uart1 {
	current-speed = <9600>;
	status = "okay";
	tx-pin = <12>;
	rx-pin = <13>;
	rts-pin = <14>;
	cts-pin = <15>;
};



&uart2 {
	status = "okay";
	current-speed = <9600>;
	tx-pin = <10>;
	rx-pin = <11>;
	rts-pin = <16>;
	cts-pin = <17>;
};

The same is in the SPM folder as nrf9160dk_nrf9160.overlay file. 

The basic UART example in the master branch provides the structure to receive data from UART. Is there any particular example to send the data from the UART ?.

I tried following this thread : https://devzone.nordicsemi.com/f/nordic-q-a/44788/nrf9160-dk-send-receive-data-from-uart1/179149#179149  , but I get an error while trying to implement that code. The error I get is in Line 24 where k_fifo_get is defined. Is there any way to fix this issue ?

Is there any other example that shows how to transmit the strings externally through a UART (UART_2 in my case).

Regards,

Adeel.

[Carl Richard]

Hello, Adeel!

I'm looking into the issue. Have you tried to observe the pins with a logic analyzer? An could you provide your prj.conf aswell? 

When it comes to examples you can have a look at the project I've attached below. It is configured to send commands over UART2. It's based on Yusukes code from this thread.
5148.hello_world.zip

And I've added the following to the overlay in SPM:

&uart2 {
	status = "okay";
	current-speed = <115200>;
	tx-pin = <1>;
	rx-pin = <0>;
	rts-pin = <14>;
	cts-pin = <15>;
};

&uart1 {
	status = "disabled";
};

Best regards,
Carl Richard

[Adeel]

Hi Carl,

I will have to look if I can get a logic analyzer to check it out. Any other way to check it out in the software ?

My prj.conf file:

CONFIG_NEWLIB_LIBC=y
CONFIG_LIBLIGHTMODBUS=y

CONFIG_GPIO=y

CONFIG_SERIAL=y
CONFIG_TRUSTED_EXECUTION_NONSECURE=y
CONFIG_UART_INTERRUPT_DRIVEN=y
CONFIG_MAIN_STACK_SIZE=4096

CONFIG_COMPILER_OPT="-DNRFX_UARTE_ENABLED=1 -DNRFX_UARTE0_ENABLED=1"
CONFIG_BSD_LIBRARY_TRACE_ENABLED=n

I also see in my devicetree_unfixed.h that the UART_2 is configured by my external pins. 

/* Generic property macros: */
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_reg {40960 /* 0xa000 */, 4096 /* 0x1000 */}
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_reg_IDX_0 40960
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_reg_IDX_1 4096
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_reg_EXISTS 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_interrupts {10 /* 0xa */, 1 /* 0x1 */}
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_interrupts_IDX_0 10
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_interrupts_IDX_1 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_interrupts_EXISTS 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_hw_flow_control 0
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_hw_flow_control_EXISTS 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_tx_pin 10
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_tx_pin_EXISTS 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_rx_pin 11
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_rx_pin_EXISTS 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_rts_pin 16
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_rts_pin_EXISTS 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_cts_pin 17
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_cts_pin_EXISTS 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_current_speed 9600
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_current_speed_EXISTS 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_label "UART_2"
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_label_EXISTS 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_status "okay"
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_status_ENUM_IDX 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_status_EXISTS 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_compatible {"nordic,nrf-uarte"}
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_compatible_IDX_0 "nordic,nrf-uarte"
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_compatible_LEN 1
#define DT_N_S_soc_S_peripheral_40000000_S_uart_a000_P_compatible_EXISTS 1

So, I presume that I have correctly configured my UART_2 (or) anything else might be required ? 

Regards,

Adeel.

[Adeel]

Hi Carl,

I tried running your example file with a slight modification in the pins and baud rate (10,11,16,17 respectively with 9600 baud rate). In the example, I see that the printk() strings get outputed to UART_0 console which is normal.

The "AT, test" string is supposed to be sent through UART_2 in this example but I don't see it being displayed. I expected that I see this string output in my external debugger console connected with my UART_2 pins. 

In any case, how would you test UART_2 in this case ? I feel a bit lost with this. Any help would be great :).

Can I test the string output by connecting my UART_2 to any COM port ?

Regards,

Adeel.

[Carl Richard]

Hi, Adeel!

I routed the UART2 to VCOM2 for testing and got the output there (my .overlay file is setup thereafter). Could you try that first maybe? Note that the output then will arrive on a different COM port than the debug messages.

In addition, P0.17 is used for board control on the nRF9160DK, as noted here. It should not be used for any other purpose.

Your devicetree_unfixed.h seems correct, and you should not need to have the CONFIG_COMPILER_OPT in your prj.conf. You can use my prj.conf for reference. 

Best regards,
Carl Richard

[Adeel]

Hi Carl,

Noted. I changed my pin numbers to (10,11,12,13). Thanks for that advice.

Could you guide me a bit about routing UART_2 to VCOM_2. The documentation says VCOM_2 is not connected to 9160. 

Also, my SPM file gives an error while building.

The error says "Include expects Filename". Which filename is the error referring to ? 

Regards,

Adeel.

[Adeel]

Hi Carl,

Is it also required to do some modification in this setting ?

I tried modifying the overlay file by adding the above settings that I found. Do I need to route the above lines to UART_2 ? 

Regards,

Adeel.

[Carl Richard]

Hi again, Adeel!

According to our documentation VCOM_2 is not connected to the nRF9160 by default, but in the sample I've attached here the UART2 is routed to VCOM_2 using overlay. As noted in the documentation VCOM_2 is connected to P0.01, P0.02, P0.15 and P0.14 of the nRF9160 GPIO. 

With regards to the error, could you try to reload the project after editing the .overlay and prj.conf files? 

It should be enough to edit the .overlay files as shown in the sample I attached.  

Best regards,
Carl Richard