product specifications of nRF8001

[Kogiso]

Hi, I'm about to perform an RF-PHY test on a module using nRF8001 to get a QDID. In that connection, I would like to know the specifications of the nRF8001.Can you tell me about the "?" Below?

IXIT Reference	Identifier	Sub-Ientifier	Value	Units
RF-PHY:P1:1	Inband Image frequency	Low frequency	?	MHz
RF-PHY:P1:2	↑	Middle frequency	?	MHz
RF-PHY:P1:3	↑	High frequency	?	MHz
RF-PHY:P2:1	Value n for Intermodulation test	Low frequency	?	Integer
RF-PHY:P2:2	↑	Middle frequency	?	Integer
RF-PHY:P2:3	↑	High frequency	?	Integer

[ketiljo]

Here you go: 

[Kogiso]

Thank you for your answer.
It was very helpful.

Let me ask you an additional question regarding the specifications of the nRF8001.

Please answer "?".

IXIT Reference	Identifier	Sub-Ientifier	Value	Units
RF-PHY:P9:1	Maximum TX packet length (MAX_TX_LENGTH)	-	?	Bytes
RF-PHY:P9:2	Maximum RX packet length (MAX_RX_LENGTH)	-	?	Bytes

[ketiljo]

Hi

Max packet length is 27 bytes

cheers,

Ketil

[Kogiso]

Thank you for your answer.
It was very helpful.

Let me ask you an additional question regarding the specifications of the nRF8001.

Please answer "?".I'm sorry for the many questions, but I look forward to your answers.

IXIT Reference	Identifier	Sub-Ientifier	Value	Units
RF-PHY:P4	Power source voltage	Nominal (NOC)	?	V
RF-PHY:P5	Normal operating temperature	Nominal (NOC)	?	°C
RF-PHY:P6:1	Operating air humidity range (relative)	Maximum	?	%
RF-PHY:P6:2	↑	Minimum	?	%
RF-PHY:P6:3	↑	Air humidity level for NOC tests	?	%
RF-PHY:P7:1	Test interface implementation	HCI or 2-wire UART	?
RF-PHY:P7:2	↑	Data rate	?	bps
RF-PHY:P9:3	Maximum TX packet length (MAX_TX_LENGTH_2M)		?	Bytes
RF-PHY:P9:4	Maximum TX packet length (MAX_TX_LENGTH_CODED_S2)		?	Bytes
RF-PHY:P9:5	Maximum TX packet length (MAX_TX_LENGTH_CODED_S8)		?	Bytes
RF-PHY:P9:6	Maximum RX packet length (MAX_RX_LENGTH_2M)		?	Bytes
RF-PHY:P9:7	Maximum RX packet length (MAX_RX_LENGTH_CODED_S2)		?	Bytes
RF-PHY:P9:8	Maximum RX packet length (MAX_RX_LENGTH_CODED_S8)		?	Bytes
RF-HY:P10:1	Maximum TX mode output power		?	dBm
RF-PHY:11:1	Inband Image Frequency (2Ms/s)	Low frequency	?	MHz
RF-PHY:11:2	↑	Middle frequency	?	MHz
RF-PHY:11:3	↑	High frequency	?	MHz
RF-PHY:12:1	Value n for Intermodulation test (2Ms/s)	Low frequency	?	Integer
RF-PHY:12:2	↑	Middle frequency	?	Integer
RF-PHY:12:3	↑	High frequency	?	Integer
RF-PHY:13:1	Inband Image Frequency (Stable Modulation Receiver)	Low frequency	?	MHz
RF-PHY:13:2	↑	Middle frequency	?	MHz
RF-PHY:13:3	↑	High frequency	?	MHz
RF-PHY:14:1	Value n for Intermodulation test (Stable Modulation Receiver)	Low frequency	?	Integer
RF-PHY:14:2	↑	Middle frequency	?	Integer
RF-PHY:14:3	↑	High frequency	?	Integer
RF-PHY:15:1	Inband Image Frequency (Stable Modulation Receiver, 2Ms/s)	Low frequency	?	MHz
RF-PHY:15:2	↑	Middle frequency	?	MHz
RF-PHY:15:3	↑	High frequency	?	MHz
RF-PHY:16:1	Value n for Intermodulation test (Stable Modulation Receiver, 2Ms/s)	Low frequency	?	Integer
RF-PHY:16:2	↑	Middle frequency	?	Integer
RF-PHY:16:3	↑	High frequency	?	Integer
RF-PHY:17	IQ Report Rate		?
RF-PHY:18	The length of the Constant Tone Extension(1Ms/s)		?	bits
RF-PHY:19	The length of the Constant Tone Extension(2Ms/s)		?	bits
RF-PHY:20	The number of antennae		?

 

[ketiljo]

Most if this doesn't apply for the nRF8001 as it doesn't support 2 Mbps, coded phy or constant tone extension. So everything from RF-PHY:P9:3 to the end is not applicable for the nRF8001. The nRG8001 only supports BLE4.0.

This should be what you're after: