How to define PIN in nrf52?

[shadab]

I want to used p1.01 and p1.2 and p0.13,so how to defined it.

I do like 

#define led0 13 to used pin p0.13 its working but how to define pin P1.01 and all

[Charlie]

Hi Shadab,

Just add 32 to the pin number of GPIO1.

[shadab]

hi charlie, I try on nrf52833 DK board but its not working

[Charlie]

Hi Shadab,

Not sure how you test this, anyway let's find a common ground.

In nRF5_SDK_17.0.2, there is a simple example on examples\peripheral\blinky. Make sure the original blink example works, then you can modify it like below to verify if pins at GPIO1 works or not. 

    /* Configure board. */
    //bsp_board_init(BSP_INIT_LEDS);
    nrf_gpio_cfg_output(NRF_GPIO_PIN_MAP(1,10));

    /* Toggle LEDs. */
    while (true)
    {
        //for (int i = 0; i < LEDS_NUMBER; i++)
        //{
            //bsp_board_led_invert(i);
            nrf_gpio_pin_toggle(42);
            nrf_delay_us(0.5);
        //}
    }

Here both NRF_GPIO_PIN_MAP(1,10) and 42 points to oin1.10. You should see the pin toggle with the help of a logic analyzer or oscilloscope.

Best regards,

Charlie

[shadab]

Hi charlie !! not working 

[Charlie]

I am working. ;-) 

Could explain what you have done by far? Did you check the original example with a logic analyzer or oscilloscope, what does it look like?

[shadab]

I used sdk17 and try the same way to config port 1 pin as output to blink external LEd but it wont work and for port 0 pin its working, I

/**
 * Copyright (c) 2014 - 2020, Nordic Semiconductor ASA
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without modification,
 * are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice, this
 *    list of conditions and the following disclaimer.
 *
 * 2. Redistributions in binary form, except as embedded into a Nordic
 *    Semiconductor ASA integrated circuit in a product or a software update for
 *    such product, must reproduce the above copyright notice, this list of
 *    conditions and the following disclaimer in the documentation and/or other
 *    materials provided with the distribution.
 *
 * 3. Neither the name of Nordic Semiconductor ASA nor the names of its
 *    contributors may be used to endorse or promote products derived from this
 *    software without specific prior written permission.
 *
 * 4. This software, with or without modification, must only be used with a
 *    Nordic Semiconductor ASA integrated circuit.
 *
 * 5. Any software provided in binary form under this license must not be reverse
 *    engineered, decompiled, modified and/or disassembled.
 *
 * THIS SOFTWARE IS PROVIDED BY NORDIC SEMICONDUCTOR ASA "AS IS" AND ANY EXPRESS
 * OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
 * OF MERCHANTABILITY, NONINFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL NORDIC SEMICONDUCTOR ASA OR CONTRIBUTORS BE
 * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
 * GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
 * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 */
/** @file
 *
 * @defgroup blinky_example_main main.c
 * @{
 * @ingroup blinky_example
 * @brief Blinky Example Application main file.
 *
 * This file contains the source code for a sample application to blink LEDs.
 *
 */

#include <stdbool.h>
#include <stdint.h>
#include "nrf_delay.h"
//#include "boards.h"
//#include "pca10000.h"
#include "nrf_gpio.h"

#define LED_ext          NRF_GPIO_PIN_MAP(0,5)
#define led0             NRF_GPIO_PIN_MAP(0,13)
#define led1             NRF_GPIO_PIN_MAP(1,8)                 // LED0 P1.8 Not working


 
/**
 * @brief Function for application main entry.
 */
int main(void)
{
    nrf_gpio_cfg_output(led0); // config the as output pin
    nrf_gpio_cfg_output(led1); // config the as output pin
    nrf_gpio_cfg_output(LED_ext); // config the as output pin


    while(1)
    {

          nrf_gpio_pin_toggle(led0);
          nrf_delay_ms(500);
          nrf_gpio_pin_toggle(led1);
          nrf_delay_ms(500);
          nrf_gpio_pin_toggle(LED_ext);
          nrf_delay_ms(500);

    }
}
/**
 *@}
 **/

shared the code below