MMD error

[Sangram singh]

I am adding  JLINK_MOITOR.c and JLINK_MONITOR_ISR_SES.s and add write 

#if CONFIG_JLINK_MONITOR_ENABLED
NVIC_SetPriority(DebugMonitor_IRQn, _PRIO_SD_LOW);
#endif

at starting of main loop but code is not compiling some error is comming pls. see error below.

Output/ble_app_uart_c_pca10040_s132 Release/Obj/JLINK_MONITOR_ISR_SES.o: In function `DebugMon_Handler':
1> D:\NORDIC\Nordic\sdk\nRF5_SDK_16.0.0\examples\ble_central\j-link-monitoring-mode-debugging-master/JLINK_MONITOR_ISR_SES.s:159: undefined reference to `JLINK_MONITOR_OnEnter'
1> Output/ble_app_uart_c_pca10040_s132 Release/Obj/JLINK_MONITOR_ISR_SES.o: In function `_WaitForJLinkCmd':
1> D:\NORDIC\Nordic\sdk\nRF5_SDK_16.0.0\examples\ble_central\j-link-monitoring-mode-debugging-master/JLINK_MONITOR_ISR_SES.s:183: undefined reference to `JLINK_MONITOR_OnPoll'
1> Output/ble_app_uart_c_pca10040_s132 Release/Obj/JLINK_MONITOR_ISR_SES.o: In function `_HandleRestartCPU':
1> D:\NORDIC\Nordic\sdk\nRF5_SDK_16.0.0\examples\ble_central\j-link-monitoring-mode-debugging-master/JLINK_MONITOR_ISR_SES.s:228: undefined reference to `JLINK_MONITOR_OnExit'
Build failed

[Amanda Hsieh]

Hi Sangram, 

Do you JLINK_MOITOR.h as this Include header files doc describes? 

-Amanda H.

[Sangram singh]

Yes, already included but error is comming.

[Sangram singh]

it can build without error now, but problem is not resolve . 

I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is the problem.

NRF_BREAKPOINT_COND;
// On assert, the system can only recover with a reset.

#ifndef DEBUG
NRF_LOG_WARNING("System reset");
NVIC_SystemReset();
#else
app_error_save_and_stop(id, pc, info);
#endif // DEBUG

[Sangram singh]

it can build without error now, but problem is not resolve . 

I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is the problem.

NRF_BREAKPOINT_COND;
// On assert, the system can only recover with a reset.

#ifndef DEBUG
NRF_LOG_WARNING("System reset");
NVIC_SystemReset();
#else
app_error_save_and_stop(id, pc, info);
#endif // DEBUG

[Sangram singh]

it can build without error now, but problem is not resolve . 

I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is the problem.

NRF_BREAKPOINT_COND;
// On assert, the system can only recover with a reset.

#ifndef DEBUG
NRF_LOG_WARNING("System reset");
NVIC_SystemReset();
#else
app_error_save_and_stop(id, pc, info);
#endif // DEBUG

[Amanda Hsieh]

Hi, 

I don't see that situation with your code 1033.ble_app_uart_c_263335.zip on nRF52DK, but I see the 
<error> nrf_ble_gatt: sd_ble_gattc_exchange_mtu_request() returned NRF_ERROR_INVALID_STATE.
<error> nrf_ble_gatt: sd_ble_gap_data_length_update() (request) on connection 0x0 returned NRF_ERROR_INVALID_STATE.

Please create a new support case for the new issue. This is away from the original scope. 

-Amanda H.

[Sangram singh]

Thanks for support now my code is working