Hello,
I use NRF Connect V3.6.1 on Windows 10 Pro - 64 bits with a seeger JLink.
I have updated the nRF programmer to v1.4.9
When I try to flash image in the nRF52840, I got the following message : 2021-06-02T13:05:33.721Z ERROR Error: Error occured when program. Errorcode: CouldNotCallFunction (0x9)
I tried with Jlink software v6.88 and v7.22.
It is the first time I try to flash this nrf52840. I didn't see this issue before using other nRF52840.
2021-06-02T13:05:33.721Z INFO Recovery procedure finished
2021-06-02T13:05:33.734Z INFO Using nrfjprog to communicate with target
2021-06-02T13:05:34.067Z INFO Using J-Link Software version 7.22
2021-06-02T13:05:34.379Z INFO Segger serial: 260115021
2021-06-02T13:05:34.379Z INFO Segger speed: 2000 kHz
2021-06-02T13:05:34.380Z INFO Segger version: J-Link V10 compiled Apr 27 2021 16:35:48
2021-06-02T13:05:34.380Z INFO Core probed: 260115021
2021-06-02T13:05:34.380Z INFO Core RAM: 256KiB
2021-06-02T13:05:34.380Z INFO Core ROM: 1024KiB in pages of 4KiB
2021-06-02T13:05:34.503Z INFO Model: NRF52840_xxAA_REV2.
2021-06-02T13:05:34.848Z INFO Core0: Reading device non-volatile memory. This may take a few seconds.
2021-06-02T13:05:35.152Z INFO Core0: UICR has been read. Click read button to read full non-volatile memory.
2021-06-02T13:06:09.001Z INFO Writing image to disable app readback protection
2021-06-02T13:06:09.838Z ERROR Error: Error occured when program. Errorcode: CouldNotCallFunction (0x9)
Lowlevel error: INVALID_PARAMETER (fffffffd)
2021-06-02T10:27:05.970Z INFO Using nrfjprog to communicate with target
2021-06-02T10:27:06.299Z INFO Using J-Link Software version 6.88
2021-06-02T10:27:06.592Z INFO Segger serial: 260115021
2021-06-02T10:27:06.592Z INFO Segger speed: 2000 kHz
2021-06-02T10:27:06.592Z INFO Segger version: J-Link V10 compiled Feb 4 2021 12:58:41
2021-06-02T10:27:06.592Z INFO Core probed: 260115021
2021-06-02T10:27:06.592Z INFO Core RAM: 256KiB
2021-06-02T10:27:06.592Z INFO Core ROM: 1024KiB in pages of 4KiB
2021-06-02T10:27:06.711Z INFO Model: NRF52840_xxAA_REV2.
2021-06-02T10:27:07.035Z INFO Core0: Reading device non-volatile memory. This may take a few seconds.
2021-06-02T10:27:07.398Z INFO Core0: UICR has been read. Click read button to read full non-volatile memory.
2021-06-02T10:27:07.507Z INFO SoftDevice detected, id 0xAE (S140 v6.1.0)
2021-06-02T10:27:13.202Z INFO Writing image to disable app readback protection
2021-06-02T10:27:14.016Z ERROR Error: Error occured when program. Errorcode: CouldNotCallFunction (0x9)
Lowlevel error: INVALID_PARAMETER (fffffffd)
Best Regards.
David
