integration usbd acd acm with DFU mesh

[Sama]

Hi,

I want to add DFU over mesh and usbd into the client example. 

I have faced an error of Multiple definitions of UARTE0_UART0_IRQHandler. I comment out the UARTE0_UART0_IRQHandler in the ses_startup. I tried to use UARTE1 for usbd by enabling the flags of uarte1 in the sdk_config. the codes are built without any compiler error but I can not see comport for usbd.

Could you please advise me?

Br,

Sama

[Sama]

Hi,

Is there any solution?

I look forward to hearing from you.

Br,

Sama

[Sama]

Hi,

I have been waiting for a long time without any response.

I managed to add USBD CDC ACM to the client example including DFU over serial, and I can send and receive data via USB port.

Now, all I want to do is send the data from the serial terminal on the detected USB PORT and then publish it over the mesh.

I have a function named "send message" as below, called when data received from the USB port.

void send_message (void) 
{
    uint32_t status=0;
    char buffer[8];///={0x44,0x61,0x74,0x61};
    uint8_t length;
    uint16_t address;
    access_message_tx_t msg;
    length= sizeof(buffer);
               if (length)
                { 
                  msg.opcode.opcode = simple_message_OPCODE_SEND ;
                  msg.opcode.company_id = 0x0059; // Nordic's company ID
      
                  msg.p_buffer = (const uint8_t *) &buffer[0];
                  msg.length =length;
            
                  

                  //SEGGER_RTT_printf(0,"Sending to group address 0x%04x\n", address);
                  status= access_model_publish(m_clients[0].model_handle, &msg);        //CHANGED TO 0 FROM 3 
                  __LOG(LOG_SRC_APP, LOG_LEVEL_INFO, "Status : %u \n", status);

                  if (status == NRF_ERROR_INVALID_STATE ||
                  status == NRF_ERROR_BUSY||status == NRF_ERROR_NO_MEM)
                   {
                     __LOG(LOG_SRC_APP, LOG_LEVEL_INFO, "Cannot send. Device is busy.\n");
                      hal_led_blink_ms(LEDS_MASK, 50, 4);
                   }
                   else
                   {
                         ERROR_CHECK(status);
                   }
                }

}

I get the error when I send data:

app_error_weak.c, 105, Mesh assert at 0x0002CDF8 (:0)
which I got with adding UART into client example, and I asked in this ticket.

I have used the addr2line tool and it returned:

....\mesh\core\src/timer_scheduler.c:218 (discriminator 1).

I have searched the Devzone, and I found out this is related to the priority level. As far as I understood, when I call a mesh API from a handler, it is needed to initialize the mesh with "NRF_MESH_IRQ_PRIORITY_LOWEST" and use the same priority level for the user interrupt (cdc_acm_user_ev_handler in this situation).

Here is the mesh init function:

static void mesh_init(void)
{
mesh_stack_init_params_t init_params =
{
.core.irq_priority = NRF_MESH_IRQ_PRIORITY_LOWEST,
.core.lfclksrc = DEV_BOARD_LF_CLK_CFG,
.core.p_uuid = NULL,
.models.models_init_cb = models_init_cb,
.models.config_server_cb = config_server_evt_cb
};

and here is the priority setting of USBD:

#ifndef NRFX_USBD_CONFIG_IRQ_PRIORITY
#define NRFX_USBD_CONFIG_IRQ_PRIORITY 6
#endif

#ifndef USBD_CONFIG_IRQ_PRIORITY
#define USBD_CONFIG_IRQ_PRIORITY 6
#endif

Any solution?

Please let me know if I should create a new ticket.

Br,
Sama

[Kaja]

Hi Sama,

this question has gone unanswered.. have you solved your problem? If not, could you create a new ticket? 

Best regards,
Kaja