Ble_app_Blinky not

[Tikull]

I have downloaded the ble_app_blinky_c_pca10056_s140 hex file to the development kit with the help of the nrf_connect windows application. I have a PCA10100 development kit. Now when I am searching this advertising device from the blinky or nrf_connect android application, the "NRF_Blinky" does not show. I have checked the development kit LED1 is constant on, and thought that the device is already advertising. So, suggest to me what can go wrong.

[awneil]

Tikull said:

I have downloaded the ble_app_blinky_c_pca10056_s140 hex file

The "_pca10056_" in the file name means that the file is for a PCA10056 board

Tikull said:

I have a PCA10100 development kit.

so that's not going to work!

[Tikull]

But I think there is no hex file available for PCA10100, and I read in one of the Q&A that the pca10056 has similar features as PCA10100, and therefore this might work. But please show me which SDK and application combination can be used in this case.

[awneil]

I never remember numbers; always have to look them up

PCA10100 = nRF52833 DK

PCA10056 = nRF52840 DK

https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_gsg_ses%2FUG%2Fgsg%2Fchips_and_sds.html

Tikull said:

please show me which SDK and application combination can be used in this case

devzone.nordicsemi.com/.../can-i-use-the-example-code-for-pca-10056-for-pca-10100

[Tikull]

Hi Awneil,

I made the changes for BOARD_PCA10056 to PCA101000 and NRF52840_XXAA to NRF52833_XXAA. Now, what changes should I make for the memory allotment when I am using the same soft device s140?.

[Einar Thorsrud]

If you are using the same SoftDevice, then the memory allocations will not change. The only exception is that you must ensure that the start address (end of SoftDevice) + x is not higher than the physically available memory (this is the same both for flash and RAM).

[Tikull]

The soft device has an address between 0x1000 to 0x26633, and the application software starts from the address 0x27000 and ends at 0x2DB63. 

Also, the RAM and FLASH memory map in the section placement Macros shows as below:

FLASH_PH_START=0x0

FLASH_PH_SIZE=0x100000

RAM_PH_START=0x20000000

RAM_PH_SIZE=0x40000

FLASH_START=0x27000

FLASH_SIZE=0xd9000

RAM_START=0x20001dc8

RAM_SIZE=0x3e238

Do this need any changes to be done?

[Einar Thorsrud]

In practice, no change is needed unless you use too much flash or RAM. If you do, it would be good to have the sized set correctly so that you would get a linker error telling you that it cannot fit.

If you want to do that, you could fix it.  First, just get the physical sizes correct. So for flash, FLASH_PH_SIZE should be 512 kB = 0x80000. For RAM, RAM_PH_SIZE should be  128 kB = 0x20000. Then just do the simple math I suggested. For instance, as FLASH_START = 0x27000 that means FLASH_SIZE = 0x80000 - 0x27000 = 0x59000. And so on.

If you happen to use a bootloader or want to reserve space for FDS etc you should set it lower. But again, this normally does not have practical implications, though it is always a good idea to ensure that you get an error as soon as possible (so build time/link time)

[Tikull]

Right now, when I am not getting any linker error, I have only changed the configuration from PCA10056 to PA10100 in ble_app_blinkx_c_pca10056_s140. But there is no LED indication on LED 1 for advertising status. What could go wrong?