Pair device address and BT_Characteristic Notify enable disable use unwanted flash space in NCS v1.4.2

[Sunil vignesh]

Hi,

I have develop the Code based on HID_KEYBOARD AND NUS code

here i also need to ADD NVS and DFU to nrf52840 device

1. Pair device address is stored in what manner. I am not able to read and delete the pair data. Is there any document for bond management

2. While using BLE NUS, BATTERY, and Custom service notification enable

I found that some data is writing on the flash . Its like increase the size of the flash . i need to control the unwanted storage . how it is possible

3. I have use storage that to be start F8000 and size is 8000 . is it possible to write and read the data in page wise ( entering direct address to write and read data).

[Susheel Nuguru]

Hi Sunil,

 You are using a bit of an older version of NCS, read more on latest v1.6.1 (at the time of this writing)

1. Pair device address is stored in what manner. I am not able to read and delete the pair data. Is there any document for bond management

 I am assuming that the bond management is done inside the Softdevice controller and no details about how it does that seems to be documented. What is your exact need for knowing this detail? What are you trying to achieve?

 

I found that some data is writing on the flash . Its like increase the size of the flash . i need to control the unwanted storage . how it is possible

 You can easily understand this by setting the brearkpoints at the flash activity API and starting the program in debug mode. The function call stack will give you the contexts of those flash acitivity.

 

3. I have use storage that to be start F8000 and size is 8000 . is it possible to write and read the data in page wise ( entering direct address to write and read data).

 It should possible to do that using the HAL drivers which are OS agnostic drivers. These HAL NVMC drivers use direct address to access flash but you should be very careful not to conflict you access with other modules in the RTOS system that think they own that flash page.

[Sunil vignesh]

1. I want to use ble_hid_keyboard program. where i need to implement DFU and Flash storage to store some data

As i know from board management file the storage location starts at  F8000 and size is 8000 if so. does DFU dual bank is working or not is any address collusion will occur or not i need to understand . and  i have tested the NVS code in that data store is based on ID not direct address . and it use extra 8 byte each id while write / read also in delete . and it have restriction that one page complete and then it move to another page .

My requirement is

page size - 4096 bytes

allocate

1st page for bond management

2nd page for sensor1 data 1KB

3rd page for sensor 2 data 2KB

if i need i can delete the 2nd page and rewrite it . if i need to delete bond then i rewrite on 1st page

2. why those service enable function are stored in flash . i found these in ble_peripheral_uart and also in BAS service enable and disable function.

how to stop writing this in flash

3. Any example codes are there for direct address flash storage

if bond management is based on softdevice means how to control it . and function to delete the bond functionality

[Sunil vignesh]

Sure, I will check this and update you shortly

[Sunil vignesh]

How to enable the required CCCD enable automatically from the device it is . means by default CCCD will be enable when the power is up or after ble connection established .

[Susheel Nuguru]

You cannot set it to enabled by default unless the devices are already bonded and the bonded device previously enabled the CCCD. Changing this behavior in gatt might need more changes than a one liner and I am not sure if it will be in compliance with the spec.

[Sunil vignesh]

Susheel,

 I will work out on this CCCD .

How to delete paired data permanently. the pairing data is controlled by softdevice itself isn't it. 

[Susheel Nuguru]

You can use bt_unpair for that.