ble button function

[Ridhi]

When i intially burn the code on dk, my dk should be in system off mode ie all functionality should be off. Then i want to press a button for 5 seconds with which the device blinks an led pattern. and if uptil  not 5 seconds button not pressed then nothing occurs and device remains in sleep mode

[Karl Ylvisaker]

Hello,

Then i want to press a button for 5 seconds with which the device blinks an led pattern. and if uptil  not 5 seconds button not pressed then nothing occurs and device remains in sleep mode

Unfortunately there is no way to delay the wakeup by 5 seconds before waking up. If you configure the device to wake on an external event through the GPIOTE PORT event, or similar, it will start the full wakeup immediately when this happens. So, if you want to see that the button is still pressed after 5 seconds you will have to add a check for this that runs as the first thing upon wakeup from SYSTEM_OFF.
Alternatively, you will need some external circuitry that delays the wakeup signal with 5 seconds, if it is crucial that the device does not wake up for the first 5 seconds.

You can see SYSTEM_OFF sleep mode demonstrated in most of the ble_peripheral examples in the SDK, such as the Nordic UART peripheral example's sleep_mode_enter function. The bsp_btn_ble module is also used to extract the startup event, i.e seeing which button is still pressed upon startup. You could do the same and have a timer start upon startup, to see if the button is held for 5 seconds. If it is not, the device may return to sleep.

Best regards,
Karl

[Ridhi]

yes Karl u are getting exactly the way i want.

i have seen the Nordic UART peripheral example's sleep_mode_enter function. Can u pls assist me in a code whereby i can check this:

initially the device is in sleep mode as when the code is flashed. Then i press a button for 5 secs to see some led pattern or advertising should start and in case if button is not held for 5 secs then it should still remain in sleep mode and if beyond 5 seconds it should nt register anything

[Karl Ylvisaker]

You can take a look at these minimal powerdown examples in this repository. The examples are made for a very old SDK version, but the general approach will be the same as for the GPIOTE peripheral in the newer SDK versions.

Start by going through the example and understanding the approach, and then continue with adding an app_timer that starts counting to 5 s upon wakeup and that could be interrupted by releasing the button, as written in my previous comment.

Let me know if you encounter any issues, or have any questions to this!

Best regards,
Karl

[Ridhi]

I am unable to create a timer setting for  button press which detects that 5 seconds when done the device will start advertising. in example u shared in that 5 seconds thing is not there. pls assist at earliest

[Karl Ylvisaker]

Hello,

Ridhi said:

I am unable to create a timer setting for  button press which detects that 5 seconds when done the device will start advertising. in example u shared in that 5 seconds thing is not there.

Yes, the example here only shows the powerdown and wake-on-button-press GPIOTE PORT event, you will have to add this along with the app_timer to your BLE example if not already present. Keep in mind that I recommended this approach when I thought you just wanted to blink some LEDs - not knowing that you wanted to do advertising following the 5 second press. In this case I would instead recommend that you begin with one of the BLE examples, and then merge this functionality into it.

I see from your other ticket that you are using the bsp module instead of the app_timer and app_buttons, which means you likely already are working out of an SDK example. Which example is this?
If you wish to use the bsp module you can change the BSP_LONG_PUSH_TIMEOUT_MS in bsp_config to 5000 ms, and then use the bsp_event_to_button_action_assign function to assign an event to the button's long push, and then have your bsp_event_handler in main.c begin advertising when it receives this event.
Try this, and let me know if you are able to start advertising following a 5 second button press.
Keep in mind that all 'long button presses' then will be 5 seconds long.

Best regards,
Karl

[Ridhi]

Hi, 

Karl i am using nrf sdk 17.1.0 examples/ble_peripherals/template nrf dk nrf52832. and s132. 

I want a that when i flash the code my device should be in system off mode,

Then when i press  a button for 5 secs then it should start advertising. and if not pressed for 5 secs it should remian in sleep mode.  i have used the BSP_LONG_PUSH_TIMEOUT_MS in bsp_config to 5000 ms but it is not working. pls assist am attaching the code as

#include <stdbool.h>
#include <stdint.h>
#include <string.h>

#include "nordic_common.h"
#include "nrf.h"
#include "app_error.h"
#include "ble.h"
#include "ble_hci.h"
#include "ble_srv_common.h"
#include "ble_advdata.h"
#include "ble_advertising.h"
#include "ble_conn_params.h"
#include "nrf_sdh.h"
#include "nrf_sdh_soc.h"
#include "nrf_sdh_ble.h"
#include "app_timer.h"
#include "fds.h"
#include "peer_manager.h"
#include "peer_manager_handler.h"
#include "bsp_btn_ble.h"
#include "sensorsim.h"
#include "ble_conn_state.h"
#include "nrf_ble_gatt.h"
#include "nrf_ble_qwr.h"
#include "nrf_pwr_mgmt.h"
#include "bsp.h"
#include "nrf_log.h"
#include "nrf_log_ctrl.h"
#include "nrf_log_default_backends.h"

#define DEVICE_NAME "Nordic_Template" /**< Name of device. Will be included in the advertising data. */
#define MANUFACTURER_NAME "NordicSemiconductor" /**< Manufacturer. Will be passed to Device Information Service. */
#define APP_ADV_INTERVAL 300 /**< The advertising interval (in units of 0.625 ms. This value corresponds to 187.5 ms). */

#define APP_ADV_DURATION 18000 /**< The advertising duration (180 seconds) in units of 10 milliseconds. */
#define APP_BLE_OBSERVER_PRIO 3 /**< Application's BLE observer priority. You shouldn't need to modify this value. */
#define APP_BLE_CONN_CFG_TAG 1 /**< A tag identifying the SoftDevice BLE configuration. */

#define MIN_CONN_INTERVAL MSEC_TO_UNITS(100, UNIT_1_25_MS) /**< Minimum acceptable connection interval (0.1 seconds). */
#define MAX_CONN_INTERVAL MSEC_TO_UNITS(200, UNIT_1_25_MS) /**< Maximum acceptable connection interval (0.2 second). */
#define SLAVE_LATENCY 0 /**< Slave latency. */
#define CONN_SUP_TIMEOUT MSEC_TO_UNITS(4000, UNIT_10_MS) /**< Connection supervisory timeout (4 seconds). */

#define FIRST_CONN_PARAMS_UPDATE_DELAY APP_TIMER_TICKS(5000) /**< Time from initiating event (connect or start of notification) to first time sd_ble_gap_conn_param_update is called (5 seconds). */
#define NEXT_CONN_PARAMS_UPDATE_DELAY APP_TIMER_TICKS(30000) /**< Time between each call to sd_ble_gap_conn_param_update after the first call (30 seconds). */
#define MAX_CONN_PARAMS_UPDATE_COUNT 3 /**< Number of attempts before giving up the connection parameter negotiation. */

#define SEC_PARAM_BOND 1 /**< Perform bonding. */
#define SEC_PARAM_MITM 0 /**< Man In The Middle protection not required. */
#define SEC_PARAM_LESC 0 /**< LE Secure Connections not enabled. */
#define SEC_PARAM_KEYPRESS 0 /**< Keypress notifications not enabled. */
#define SEC_PARAM_IO_CAPABILITIES BLE_GAP_IO_CAPS_NONE /**< No I/O capabilities. */
#define SEC_PARAM_OOB 0 /**< Out Of Band data not available. */
#define SEC_PARAM_MIN_KEY_SIZE 7 /**< Minimum encryption key size. */
#define SEC_PARAM_MAX_KEY_SIZE 16 /**< Maximum encryption key size. */

#define DEAD_BEEF 0xDEADBEEF /**< Value used as error code on stack dump, can be used to identify stack location on stack unwind. */

#define BT0_LONG_PUSH BSP_EVENT_KEY_0
static bool startup= true; /**< flag for startup mode. */

NRF_BLE_GATT_DEF(m_gatt); /**< GATT module instance. */
NRF_BLE_QWR_DEF(m_qwr); /**< Context for the Queued Write module.*/
BLE_ADVERTISING_DEF(m_advertising); /**< Advertising module instance. */

static uint16_t m_conn_handle = BLE_CONN_HANDLE_INVALID; /**< Handle of the current connection. */

/* YOUR_JOB: Declare all services structure your application is using
* BLE_XYZ_DEF(m_xyz);
*/

// YOUR_JOB: Use UUIDs for service(s) used in your application.
static ble_uuid_t m_adv_uuids[] = /**< Universally unique service identifiers. */
{
{BLE_UUID_DEVICE_INFORMATION_SERVICE, BLE_UUID_TYPE_BLE}
};

//static void advertising_start(bool erase_bonds);

/**@brief Callback function for asserts in the SoftDevice.
*
* @details This function will be called in case of an assert in the SoftDevice.
*
* @warning This handler is an example only and does not fit a final product. You need to analyze
* how your product is supposed to react in case of Assert.
* @warning On assert from the SoftDevice, the system can only recover on reset.
*
* @param[in] line_num Line number of the failing ASSERT call.
* @param[in] file_name File name of the failing ASSERT call.
*/
void assert_nrf_callback(uint16_t line_num, const uint8_t * p_file_name)
{
app_error_handler(DEAD_BEEF, line_num, p_file_name);
}

/**@brief Function for starting advertising.
*/
static void advertising_start()
{

ret_code_t ret;
ret = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST);
APP_ERROR_CHECK(ret);
}

/**@brief Function for the Timer initialization.
*
* @details Initializes the timer module. This creates and starts application timers.
*/
static void timers_init(void)
{
// Initialize timer module.
ret_code_t err_code = app_timer_init();
APP_ERROR_CHECK(err_code);

// Create timers.

/* YOUR_JOB: Create any timers to be used by the application.
Below is an example of how to create a timer.
For every new timer needed, increase the value of the macro APP_TIMER_MAX_TIMERS by
one.
ret_code_t err_code;
err_code = app_timer_create(&m_app_timer_id, APP_TIMER_MODE_REPEATED, timer_timeout_handler);
APP_ERROR_CHECK(err_code); */
}

/**@brief Function for the GAP initialization.
*
* @details This function sets up all the necessary GAP (Generic Access Profile) parameters of the
* device including the device name, appearance, and the preferred connection parameters.
*/
static void gap_params_init(void)
{
ret_code_t err_code;
ble_gap_conn_params_t gap_conn_params;
ble_gap_conn_sec_mode_t sec_mode;

BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode);

err_code = sd_ble_gap_device_name_set(&sec_mode,
(const uint8_t *)DEVICE_NAME,
strlen(DEVICE_NAME));
APP_ERROR_CHECK(err_code);

/* YOUR_JOB: Use an appearance value matching the application's use case.
err_code = sd_ble_gap_appearance_set(BLE_APPEARANCE_);
APP_ERROR_CHECK(err_code); */

memset(&gap_conn_params, 0, sizeof(gap_conn_params));

gap_conn_params.min_conn_interval = MIN_CONN_INTERVAL;
gap_conn_params.max_conn_interval = MAX_CONN_INTERVAL;
gap_conn_params.slave_latency = SLAVE_LATENCY;
gap_conn_params.conn_sup_timeout = CONN_SUP_TIMEOUT;

err_code = sd_ble_gap_ppcp_set(&gap_conn_params);
APP_ERROR_CHECK(err_code);
}

/**@brief Function for initializing the GATT module.
*/
static void gatt_init(void)
{
ret_code_t err_code = nrf_ble_gatt_init(&m_gatt, NULL);
APP_ERROR_CHECK(err_code);
}

/**@brief Function for handling Queued Write Module errors.
*
* @details A pointer to this function will be passed to each service which may need to inform the
* application about an error.
*
* @param[in] nrf_error Error code containing information about what went wrong.
*/
static void nrf_qwr_error_handler(uint32_t nrf_error)
{
APP_ERROR_HANDLER(nrf_error);
}

/**@brief Function for handling the YYY Service events.
* YOUR_JOB implement a service handler function depending on the event the service you are using can generate
*
* @details This function will be called for all YY Service events which are passed to
* the application.
*
* @param[in] p_yy_service YY Service structure.
* @param[in] p_evt Event received from the YY Service.
*
*
static void on_yys_evt(ble_yy_service_t * p_yy_service,
ble_yy_service_evt_t * p_evt)
{
switch (p_evt->evt_type)
{
case BLE_YY_NAME_EVT_WRITE:
APPL_LOG("[APPL]: charact written with value %s. ", p_evt->params.char_xx.value.p_str);
break;

default:
// No implementation needed.
break;
}
}
*/

/**@brief Function for initializing services that will be used by the application.
*/
static void services_init(void)
{
ret_code_t err_code;
nrf_ble_qwr_init_t qwr_init = {0};

// Initialize Queued Write Module.
qwr_init.error_handler = nrf_qwr_error_handler;

err_code = nrf_ble_qwr_init(&m_qwr, &qwr_init);
APP_ERROR_CHECK(err_code);

/* YOUR_JOB: Add code to initialize the services used by the application.
ble_xxs_init_t xxs_init;
ble_yys_init_t yys_init;

// Initialize XXX Service.
memset(&xxs_init, 0, sizeof(xxs_init));

xxs_init.evt_handler = NULL;
xxs_init.is_xxx_notify_supported = true;
xxs_init.ble_xx_initial_value.level = 100;

err_code = ble_bas_init(&m_xxs, &xxs_init);
APP_ERROR_CHECK(err_code);

// Initialize YYY Service.
memset(&yys_init, 0, sizeof(yys_init));
yys_init.evt_handler = on_yys_evt;
yys_init.ble_yy_initial_value.counter = 0;

err_code = ble_yy_service_init(&yys_init, &yy_init);
APP_ERROR_CHECK(err_code);
*/
}

/**@brief Function for handling the Connection Parameters Module.
*
* @details This function will be called for all events in the Connection Parameters Module which
* are passed to the application.
* @note All this function does is to disconnect. This could have been done by simply
* setting the disconnect_on_fail config parameter, but instead we use the event
* handler mechanism to demonstrate its use.
*
* @param[in] p_evt Event received from the Connection Parameters Module.
*/
static void on_conn_params_evt(ble_conn_params_evt_t * p_evt)
{
ret_code_t err_code;

if (p_evt->evt_type == BLE_CONN_PARAMS_EVT_FAILED)
{
err_code = sd_ble_gap_disconnect(m_conn_handle, BLE_HCI_CONN_INTERVAL_UNACCEPTABLE);
APP_ERROR_CHECK(err_code);
}
}

/**@brief Function for handling a Connection Parameters error.
*
* @param[in] nrf_error Error code containing information about what went wrong.
*/
static void conn_params_error_handler(uint32_t nrf_error)
{
APP_ERROR_HANDLER(nrf_error);
}

/**@brief Function for initializing the Connection Parameters module.
*/
static void conn_params_init(void)
{
ret_code_t err_code;
ble_conn_params_init_t cp_init;

memset(&cp_init, 0, sizeof(cp_init));

cp_init.p_conn_params = NULL;
cp_init.first_conn_params_update_delay = FIRST_CONN_PARAMS_UPDATE_DELAY;
cp_init.next_conn_params_update_delay = NEXT_CONN_PARAMS_UPDATE_DELAY;
cp_init.max_conn_params_update_count = MAX_CONN_PARAMS_UPDATE_COUNT;
cp_init.start_on_notify_cccd_handle = BLE_GATT_HANDLE_INVALID;
cp_init.disconnect_on_fail = false;
cp_init.evt_handler = on_conn_params_evt;
cp_init.error_handler = conn_params_error_handler;

err_code = ble_conn_params_init(&cp_init);
APP_ERROR_CHECK(err_code);
}

/**@brief Function for starting timers.
*/
static void application_timers_start(void)
{
/* YOUR_JOB: Start your timers. below is an example of how to start a timer.
ret_code_t err_code;
err_code = app_timer_start(m_app_timer_id, TIMER_INTERVAL, NULL);
APP_ERROR_CHECK(err_code); */

}

/**@brief Function for putting the chip into sleep mode.
*
* @note This function will not return.
*/
static void sleep_mode_enter(void)
{
ret_code_t err_code;

err_code = bsp_indication_set(BSP_INDICATE_IDLE);
APP_ERROR_CHECK(err_code);

// Prepare wakeup buttons.
err_code = bsp_btn_ble_sleep_mode_prepare();
APP_ERROR_CHECK(err_code);

// Go to system-off mode (this function will not return; wakeup will cause a reset).
err_code = sd_power_system_off();
APP_ERROR_CHECK(err_code);
}

/**@brief Function for handling advertising events.
*
* @details This function will be called for advertising events which are passed to the application.
*
* @param[in] ble_adv_evt Advertising event.
*/
static void on_adv_evt(ble_adv_evt_t ble_adv_evt)
{
ret_code_t err_code;

switch (ble_adv_evt)
{
case BLE_ADV_EVT_FAST:
NRF_LOG_INFO("Fast advertising.");
err_code = bsp_indication_set(BSP_INDICATE_ADVERTISING);
APP_ERROR_CHECK(err_code);
break;

case BLE_ADV_EVT_IDLE:
sleep_mode_enter();
break;

default:
break;
}
}

/**@brief Function for handling BLE events.
*
* @param[in] p_ble_evt Bluetooth stack event.
* @param[in] p_context Unused.
*/
static void ble_evt_handler(ble_evt_t const * p_ble_evt, void * p_context)
{
ret_code_t err_code = NRF_SUCCESS;

switch (p_ble_evt->header.evt_id)
{
case BLE_GAP_EVT_DISCONNECTED:
NRF_LOG_INFO("Disconnected.");
// LED indication will be changed when advertising starts.
break;

case BLE_GAP_EVT_CONNECTED:
NRF_LOG_INFO("Connected.");
err_code = bsp_indication_set(BSP_INDICATE_CONNECTED);
APP_ERROR_CHECK(err_code);
m_conn_handle = p_ble_evt->evt.gap_evt.conn_handle;
err_code = nrf_ble_qwr_conn_handle_assign(&m_qwr, m_conn_handle);
APP_ERROR_CHECK(err_code);
break;

case BLE_GAP_EVT_PHY_UPDATE_REQUEST:
{
NRF_LOG_DEBUG("PHY update request.");
ble_gap_phys_t const phys =
{
.rx_phys = BLE_GAP_PHY_AUTO,
.tx_phys = BLE_GAP_PHY_AUTO,
};
err_code = sd_ble_gap_phy_update(p_ble_evt->evt.gap_evt.conn_handle, &phys);
APP_ERROR_CHECK(err_code);
} break;

case BLE_GATTC_EVT_TIMEOUT:
// Disconnect on GATT Client timeout event.
NRF_LOG_DEBUG("GATT Client Timeout.");
err_code = sd_ble_gap_disconnect(p_ble_evt->evt.gattc_evt.conn_handle,
BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
APP_ERROR_CHECK(err_code);
break;

case BLE_GATTS_EVT_TIMEOUT:
// Disconnect on GATT Server timeout event.
NRF_LOG_DEBUG("GATT Server Timeout.");
err_code = sd_ble_gap_disconnect(p_ble_evt->evt.gatts_evt.conn_handle,
BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
APP_ERROR_CHECK(err_code);
break;

default:
// No implementation needed.
break;
}
}

/**@brief Function for initializing the BLE stack.
*
* @details Initializes the SoftDevice and the BLE event interrupt.
*/
static void ble_stack_init(void)
{
ret_code_t err_code;

err_code = nrf_sdh_enable_request();
APP_ERROR_CHECK(err_code);

// Configure the BLE stack using the default settings.
// Fetch the start address of the application RAM.
uint32_t ram_start = 0;
err_code = nrf_sdh_ble_default_cfg_set(APP_BLE_CONN_CFG_TAG, &ram_start);
APP_ERROR_CHECK(err_code);

// Enable BLE stack.
err_code = nrf_sdh_ble_enable(&ram_start);
APP_ERROR_CHECK(err_code);

// Register a handler for BLE events.
NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, NULL);
}

/**@brief Clear bond information from persistent storage.
*/
static void delete_bonds(void)
{
ret_code_t err_code;

NRF_LOG_INFO("Erase bonds!");

err_code = pm_peers_delete();
APP_ERROR_CHECK(err_code);
}

/**@brief Function for initializing the Advertising functionality.
*/
static void advertising_init()
{
ret_code_t err_code;
ble_advertising_init_t init;

memset(&init, 0, sizeof(init));

init.advdata.name_type = BLE_ADVDATA_FULL_NAME;
init.advdata.include_appearance = true;
init.advdata.flags = BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;
init.advdata.uuids_complete.uuid_cnt = sizeof(m_adv_uuids) / sizeof(m_adv_uuids[0]);
init.advdata.uuids_complete.p_uuids = m_adv_uuids;

init.config.ble_adv_fast_enabled = true;
init.config.ble_adv_fast_interval = APP_ADV_INTERVAL;
init.config.ble_adv_fast_timeout = APP_ADV_DURATION;

init.evt_handler = on_adv_evt;

err_code = ble_advertising_init(&m_advertising, &init);
APP_ERROR_CHECK(err_code);

ble_advertising_conn_cfg_tag_set(&m_advertising, APP_BLE_CONN_CFG_TAG);
}

/**@brief Function for handling events from the BSP module.
*
* @param[in] event Event generated when button is pressed.
*/
static void bsp_event_handler(bsp_event_t event)
{
ret_code_t err_code;

switch (event)
{
case BT0_LONG_PUSH:

if(startup)

{ // first time advertising mode

//Initialising functions for BLE
gap_params_init();
gatt_init();
services_init();
advertising_init();
conn_params_init();
advertising_start();
}

else{
NRF_LOG_INFO("Data logging Mode.");
}
break;

case BSP_EVENT_SLEEP:
sleep_mode_enter();
break; // BSP_EVENT_SLEEP

case BSP_EVENT_DISCONNECT:
err_code = sd_ble_gap_disconnect(m_conn_handle,
BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
if (err_code != NRF_ERROR_INVALID_STATE)
{
APP_ERROR_CHECK(err_code);
}
break; // BSP_EVENT_DISCONNECT

case BSP_EVENT_WHITELIST_OFF:
if (m_conn_handle == BLE_CONN_HANDLE_INVALID)
{
err_code = ble_advertising_restart_without_whitelist(&m_advertising);
if (err_code != NRF_ERROR_INVALID_STATE)
{
APP_ERROR_CHECK(err_code);
}
}
break; // BSP_EVENT_KEY_0

default:
break;
}
}

/**@brief Function for initializing buttons and leds.
*
* @param[out] p_erase_bonds Will be true if the clear bonding button was pressed to wake the application up.
*/
static void buttons_leds_init()
{
ret_code_t err_code;
bsp_event_t startup_event;

err_code = bsp_init(BSP_INIT_LEDS | BSP_INIT_BUTTONS, bsp_event_handler);
APP_ERROR_CHECK(err_code);

err_code = bsp_btn_ble_init(NULL, &startup_event);
APP_ERROR_CHECK(err_code);

err_code = bsp_event_to_button_action_assign(BSP_BOARD_BUTTON_0, BSP_BUTTON_ACTION_LONG_PUSH, BT0_LONG_PUSH);
APP_ERROR_CHECK(err_code);

}

/**@brief Function for initializing the nrf log module.
*/
static void log_init(void)
{
ret_code_t err_code = NRF_LOG_INIT(NULL);
APP_ERROR_CHECK(err_code);

NRF_LOG_DEFAULT_BACKENDS_INIT();
}

/**@brief Function for initializing power management.
*/
static void power_management_init(void)
{
ret_code_t err_code;
err_code = nrf_pwr_mgmt_init();
APP_ERROR_CHECK(err_code);
}

/**@brief Function for handling the idle state (main loop).
*
* @details If there is no pending log operation, then sleep until next the next event occurs.
*/
static void idle_state_handle(void)
{
if (NRF_LOG_PROCESS() == false)
{
nrf_pwr_mgmt_run();
}
}

/**@brief Function for application main entry.
*/
int main(void)
{
log_init(); // no need for final project
timers_init();
buttons_leds_init();

power_management_init();
ble_stack_init();
// Initialize.

// advertising_start(erase_bonds);

// Enter main loop.
for (;;)
{
idle_state_handle();
}
}

/**
* @}
*/

[Karl Ylvisaker]

Hello,

Please always use the Insert -> Code option when sharing code here in DevZone.

Ridhi said:

I want a that when i flash the code my device should be in system off mode,

When you have implemented the check for the 5 seconds button press the device should always go into S

Ridhi said:

i am using nrf sdk 17.1.0 examples/ble_peripherals/template nrf dk nrf52832. and s132. 

Thank you for specifying.

Ridhi said:

Then when i press  a button for 5 secs then it should start advertising. and if not pressed for 5 secs it should remian in sleep mode.  i have used the BSP_LONG_PUSH_TIMEOUT_MS in bsp_config to 5000 ms but it is not working. pls assist am attaching the code as

This is one way you could go about implementing this:
In the timers_init you should create and start a 5 second timer that will call sleep_mode_enter when it expires.
You should then have the 5 second button long push stop this timer, and start the advertising. The button_led_init should therefore happen before the timers_init, so that the button press always leads the sleep timer.
You will also need to check whether the extracted startup event in the button_leds_init was the 5 second button, and if so you need to call the bsp_button_event_handler manually with the extracted startup event. You should also consider what the correct handling for if the button is released before 5 seconds has passed, but then immediately pressed again. Should this restart the sleep timer, for example?
Also, what is the timer_timeout_handler function?

Please try this, and let me know if you achieve the desired functionality.

Best regards,
Karl

[Ridhi]

Hi Karl,

I have nrf53832 dev kit sft devc s132 and sdk 17.1.0

i have a code where initially the system is off

then i press button 1 on dev kit for 5 secs then the led 1 glows.

also, if multiply by 2 in this value 65534*100 i can press button for 10 secs and then the led 1 glows and works as desired.BOTH SENSOR - system off.rar

My issue is that from where this 65534 value is comming which sets button press to be 5 secs. Like my issue is that now i want tht i should press button for say 3 secs then what will i use?

[Karl Ylvisaker]

Ridhi said:

i have a code where initially the system is off

then i press button 1 on dev kit for 5 secs then the led 1 glows.

Great, I am glad to hear that you have successfully implemented the functionality you desired!
For clarity I also would like to emphasize that the DK is actually powered on for the 5 seconds you are pressing the button as well, so it technically wakes immediately upon the button press.

Ridhi said:

My issue is that from where this 65534 value is comming which sets button press to be 5 secs. Like my issue is that now i want tht i should press button for say 3 secs then what will i use?

I can not open your project unless you share it as a .zip file.
I am not sure where the value you are referencing is coming from either, but if you are using the TIMER or APP_TIMER there are macros and functions to convert from milliseconds to timer ticks for you, so you do not have to input the raw tick values yourself. I recommend that you use these macros or functions instead of inputting the raw tick values directly.

Best regards,
Karl

[Ridhi]

BOTH SENSOR - system off.zip

[Karl Ylvisaker]

Please specify which section of the code you are referring to in your previous comment, so I know what you would like me to take a look at. Please be as specific as possible.

[Ridhi]

in main()

while(bsp_button_is_pressed(BSP_BOARD_BUTTON_0) == true)
    {
				if (button_tick >= 65534*100) //need to identify for 3 secs button pres
			
					{
						
						button_tick = 0;
						bsp_indication_set(BSP_INDICATE_USER_STATE_0);
						NRF_LOG_INFO("BeforeFivesec"); 
						sleepFlag = 0;
						break;
				}
					button_tick++;
	  }