Problem to using p0.18(RESET Pin) for GPIO

[butumout]

I'm using nrf52833 on custom board.

And I need to using RESET pin to GPIO for battery charging detection.

I found CONFIG_GPIO_AS_PINRESET is configuration RESET pin,

and if I undefined CONFIG_GPIO_AS_PINRESET, p0.18 pin will be working GPIO.

But, many of case was failed.

I think,

If I undefined CONFIG_GPIO_AS_PINRESET,

MCU was nothing to handling NRF_UICR->PSELRESET register.

But NRF_UICR->PSELRESET registor still configuration like RESET pin(like dummy data ).

So, even if CONFIG_GPIO_AS_PINRESET is undefined, MCU still working p0.18 pin is configuration by RESET pin.

That's why I think, it's need to setting NRF_UICR->PSELRESET register to disconnect(connect bit to set '1') when CONFIG_GPIO_AS_PINRESET is undefined.

[butumout]

HI.

I'm already solved this problem like t his.

    #if defined (CONFIG_GPIO_AS_PINRESET)
        if (((NRF_UICR->PSELRESET[0] & UICR_PSELRESET_CONNECT_Msk) != (UICR_PSELRESET_CONNECT_Connected << UICR_PSELRESET_CONNECT_Pos)) ||
            ((NRF_UICR->PSELRESET[1] & UICR_PSELRESET_CONNECT_Msk) != (UICR_PSELRESET_CONNECT_Connected << UICR_PSELRESET_CONNECT_Pos))){
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_UICR->PSELRESET[0] = 18;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_UICR->PSELRESET[1] = 18;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Ren << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NVIC_SystemReset();
        }
    #else
        if (((NRF_UICR->PSELRESET[0] & UICR_PSELRESET_CONNECT_Msk) != (UICR_PSELRESET_CONNECT_Disconnected << UICR_PSELRESET_CONNECT_Pos)) ||
            ((NRF_UICR->PSELRESET[1] & UICR_PSELRESET_CONNECT_Msk) != (UICR_PSELRESET_CONNECT_Disconnected << UICR_PSELRESET_CONNECT_Pos))){
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_UICR->PSELRESET[0] = 0x80000000;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_UICR->PSELRESET[1] = 0x80000000;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Ren << NVMC_CONFIG_WEN_Pos;
            while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
            NVIC_SystemReset();
        }
    #endif