This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Calculation of time

lgs over 4 years ago

Hi Team,

Does it have some functions to calculate the working time from the starting point on nrf52850 chips?

Best,

Gaosheng

Top Replies

Karl Ylvisaker over 4 years ago in reply to lgs +1 verified

From your other tickets it seems that you are using the nRF5 SDK, in which case you can see a demonstration of the RTC peripheral usage in the RTC peripheral example , or you could read about the app_timer…

Parents

0 Karl Ylvisaker over 4 years ago

Hello,

The MSP430FR5994 is not a Nordic Semiconductor product, so we do not provide technical support for it here in the DevZone forum.
I would recommend that you open a ticket for this in a Texas Instrument forum instead.

Best regards,
Karl
Cancel
Vote Up 0 Vote Down

Cancel
0 lgs over 4 years ago in reply to Karl Ylvisaker

Sorry for typing errors, I mean nrf52840 chips.
Cancel
Vote Up 0 Vote Down

Cancel
0 Karl Ylvisaker over 4 years ago in reply to lgs

Oh, I see - thank you for clarifying.

There is no innate function for checking time since chip startup, but you could start a timer at the beginning of your main function and read that out later to see how long time the device has been on for. This will however only capture that time that code has been executing on the chip, so it does not encompass the time it took to power up and run the code to start the timer.

What are your requirements for your timing - how accurate does it need to be, and what resolution are you looking for?

Best regards,
Karl
Cancel
Vote Up 0 Vote Down

Cancel

Reply

0 Karl Ylvisaker over 4 years ago in reply to lgs

Oh, I see - thank you for clarifying.

There is no innate function for checking time since chip startup, but you could start a timer at the beginning of your main function and read that out later to see how long time the device has been on for. This will however only capture that time that code has been executing on the chip, so it does not encompass the time it took to power up and run the code to start the timer.

What are your requirements for your timing - how accurate does it need to be, and what resolution are you looking for?

Best regards,
Karl
Cancel
Vote Up 0 Vote Down

Cancel

Children

0 lgs over 4 years ago in reply to Karl Ylvisaker

Hi Karl,

My requirement is to calculate the time from the starting point to the drown-out. I want to preserve the value on flash memory. Then next time, I can read from the flash memory. The resolution I think it is ms level.

Best,

Gaosheng
Cancel
Vote Up 0 Vote Down

Cancel
0 Karl Ylvisaker over 4 years ago in reply to lgs

Hello again, Gaosheng

Aha, I see - then I suggest setting up an RTC or app_timer instance at the beginning of your main(), and then write its value to FLASH every so often. Using the RTC or app_timer instance will have a lower power consumption as well as a lower accuracy than using the TIMER peripheral for this task. Since you only need accuracy in the ms magnitude it will be totally fine to use the low power options for this.

Best regards,
Karl
Cancel
Vote Up 0 Vote Down

Cancel
0 lgs over 4 years ago in reply to Karl Ylvisaker

Hi Karl,

Thanks! The last question: Do you have any examples for recording time?

With best regards,

Gaosheng
Cancel
Vote Up 0 Vote Down

Cancel
+1 Karl Ylvisaker over 4 years ago in reply to lgs

From your other tickets it seems that you are using the nRF5 SDK, in which case you can see a demonstration of the RTC peripheral usage in the RTC peripheral example, or you could read about the app_timer library here - the app_timer library is also extensively used in the BLE peripheral examples in the SDK, if you want to see its usage demonstrated.

Best regards,
Karl
Cancel
Vote Up +1 Vote Down

Cancel