Using UART1 for the serial communication

[Stjepan Brlecic]

I am using nRF5340DK and would like to send and receive data to computer via UART1 and pins "TX", "RX", "CTS" and "RTS" using USB TO RS232 SERIAL CONVERTER.

This way I would keep UART0 for logging.

But I can't receive or send data via UART1.

I'm using the Segger IDE and the Peripheral_UART for the first nRF5340 DK board and the Central_UART example for the second board.

Im trying to use UART1 in Peripheral_UART example.

For now I changed settings for UART1 in zephyr.dst file

uart1: uart@9000 {
  compatible = "nordic,nrf-uarte";
  reg = < 0x9000 0x1000 >;
  interrupts = < 0x9 0x1 >;
  status = "okay";
  label = "UART_1";
  current-speed = < 0x4b00 >;
  tx-pin = < 0x21 >;
  rx-pin = < 0x20 >;
  rts-pin = < 0x0b >;
  cts-pin = < 0x0a >;
};

And i added in autoconfig.h

#define CONFIG_NRFX_UARTE1 1
#define CONFIG_UART_NRFX 1
#define CONFIG_UART_1_NRF_UARTE 1
#define CONFIG_UART_1_ENHANCED_POLL_OUT 1
#define CONFIG_UART_1_ASYNC 1
#define CONFIG_UART_1_NRF_TX_BUFFER_SIZE 32

It won't work with UART1.

When I switch back to UART0 it works fine.

What could be a problem?

[Øivind]

Hi,

Do not make changes to files in the build folder. Instead, make config changes in peripheral_uart/prj.conf and make dts changes in an overlay file named <board>.overlay. For example nrf5340dk_nrf5340_cpuapp.overlay

The only change you need to make to the prj.conf will be to add CONFIG_NRFX_UARTE1=y and CONFIG_BT_NUS_UART_DEV="UART_1"

In the overlay file, use "&uart1 {}" instead of "uart1: uart@9000 {}"

Try these changes instead, and let me know if you still encounter issues.

[Stjepan Brlecic]

Hi,

I rollback all the changes to Peripheral_UART project,

then I add

CONFIG_NRFX_UARTE1=y
CONFIG_BT_NUS_UART_DEV="UART_1"

to the prj.conf file 

and I add new file "build_nrf5340dk_nrf5340_cpuapp\zephyr\nrf5340dk_nrf5340_cpuapp.overlay"

with inside 

&uart1 {
 compatible = "nordic,nrf-uarte";
 reg = < 0x9000 0x1000 >;
 interrupts = < 0x9 0x1 >;
 status = "okay";
 label = "UART_1";
 current-speed = < 0x4b00 >;
 tx-pin = < 0x21 >;
 rx-pin = < 0x20 >;
 rts-pin = < 0x0b >;
 cts-pin = < 0x0a >;
};

But it doesn't work.

It gives me an exception --> ENXIO 6  /**< No such device or address */

uart = device_get_binding(DT_LABEL(DT_NODELABEL(uart1)));
if (!uart) {
  printk("UART binding failed");
  return -ENXIO;
}

I even tried the same changes in the Central_UART project but still get the same exception.

If I change back to uart0 everything works like before.

I'm using SDK 1.6.1.

[Stjepan Brlecic]

As i suspected the .dts file is not changing, do you perhaps know what the reason would be?

I change the overlay file and then in Segger IDE run these 2 commands.

Is that enough? 

[Øivind]

Oh, no that is not enough. When using SES, you need to run "Project->Run CMake" after changes to overlay files, prj.conf etc.

[Stjepan Brlecic]

Now when I use run "Project-> Run CMake" .dts file is changed and looks fine.

uart1: arduino_serial: uart@9000 {
  compatible = "nordic,nrf-uarte";
  reg = < 0x9000 0x1000 >;
  interrupts = < 0x9 0x1 >;
  status = "okay";
  label = "UART_1";
  current-speed = < 0x4b00 >;
  tx-pin = < 0x22 >;
  rx-pin = < 0x23 >;
};

Now I use pins 34 --> P1.02 and 35 --> P1.03 as you recommended.

Wires -> ORANGE -> TXD; YELLOW -> RXD;

An error that occurred before is gone,

but a new error occurs...

OUTPUT

Not able to allocate UART receive buffer2

CODE

static void uart_work_handler(struct k_work *item)
{
      struct uart_data_t *buf;

      buf = k_malloc(sizeof(*buf));
      if (buf) {
            buf->len = 0;
      } else {
            printk("Not able to allocate UART receive buffer2\n");
            k_work_reschedule(&uart_work, UART_WAIT_FOR_BUF_DELAY);
            return;
      }

      uart_rx_enable(uart, buf->data, sizeof(buf->data), UART_WAIT_FOR_RX);
}

I believe the problem is here buf = k_malloc(sizeof(*buf));

, do you have any idea why this is happening?

Do I miss any other settings?

[Øivind]

Does this happen the first time you use k_malloc(), or after running for a time? If it runs for a time before failing, make sure that the buffers are being freed properly. If you are changing anything about how the buffers are made or used, you may be avoiding the k_free(buf).

Have you modified the sample other than changing to uart1?

[Stjepan Brlecic]

Does this happen the first time you use k_malloc() --> No

When I run Perhiperal_UART example everything starts normally, without error ...
An error occurs when I enter something on UART1 on a connected computer, in my case USB TO RS232 SERIAL CONVERTER on COM75 then several times the k_malloc() is done correctly and after a few times an error starts to occur

OUTPUT

Bluetooth initializedStarting Nordic UART service example
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Allocate UART receive buffer0 DONE
Allocate UART receive buffer1 DONE
Not able to allocate UART receive buffer0
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2
Not able to allocate UART receive buffer2

and continue to report Not able to allocate UART receive buffer2

Have you modified the sample other than changing to uart1? --> No, I only added printk() in a few places

[Øivind]

Could you zip the project and attach it here using Insert->Image/video/file ?

Looks like the ble_write_thread is stuck on the k_sem_take and is not able to free the buffers.

[Stjepan Brlecic]

I included zip file peripheral_uart_20220208

peripheral_uart_20220208.zip

Is there another simpler SEGGER example of using a UART without Bluetooth in SDK 1.6.1?

[Stjepan Brlecic]

Looks like the problem was in the bad USB TO RS232 SERIAL adapter ...
It works now...

I still needed help with redirecting the communication on uart1, so thank you for that, you were very helpful, now everything works.