No Connected Deivce for Thingy:53 board

[Divya_uni_ulm]

Hello,

So, as per the requirement for my project I need to program the Thing:53 using Visual Studio code programmer following the instruction as provided in the below link:

https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_thingy53.html#thingy53-compatible-applications

As I am new to thingy:53, I tried to run the sample code for theThingy as provided on the link:

I have tried to set the build configuration as mentioned for the desired sample (Bluetooth: Peripheral LBS):

changes for the build are as mentioned below:

After finishing up the build configuration I tried to connect my device to the laptop but even after the build the software is not able to detect Thingy:53 in the connected device section

So, I have a query that do you know why am I not able to find out the device?

It would be highly appreciable if you can help me out to solve this problem.

Regards,

Divya

[Divya_uni_ulm]

Hallo Elfving,

Thank you for your response, but is there any way out if I can use Thingy53 for my project?

Regards,

Divya 

[Elfving]

Divya_uni_ulm said:

is there any way out if I can use Thingy53 for my project

Yes, you can get a Programmer to use with it, ie. a nRF5340Dk.

Regards,

Elfving

[Divya_uni_ulm]

Hello Elfving,

Right now, I am working on my project I am using TensorFlow to develop my code, and then I have trained the model and then converted it into tflite finally into a .hex file. 

So, after careful reading and soem suggestion provided by you, I have understood that there are 2 possible ways where I can flash the desired code.

1. Using a debugger as well, or using an SDK kit: nRF5340DK 
2. TF lite micro 

As mentioned in this previous post regarding Thingy:

https://devzone.nordicsemi.com/f/nordic-q-a/91248/thingy53-support-for-tensorflow-lite

 

So, I have a few queries related to TF Lite Micro as mentioned in the link below:

https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/nrf-tensorflow-support

1. Is there any link/document/blog related to programming microcontrollers using Tensorflow Lite Micro?
2. As mentioned in the link, it is a little bit confusing for me but can we use this method only with SDK, or can we also program Thingy:53 with sample code to test and check the behavior?
3. Though I have understood that programming with the debugger or nRF5340DK board is one way to solve this issue but do you think we can use TF lite Micro to program Thingy:53, as well?

It would be very helpful is you can help me to resolve this confusion and help me out with the best solution to program Thingy. 

Regards,

Divya

[Elfving]

First of all, let me explain some terms and acronyms:

• An external debugger would typically be something like a Jlink commander (google it if you want to know what it looks like).
• A DK is a Development Kit, that is typically a board with an SoC along with an accompanying debugging chip. This is an example of DK, the nRF5340DK is another.
• An SDK is a Software development Kit. The SDKs we have available are the nRF5 SDK, and the nRF Connect SDK.

In order to flash an SoC, like the nRF5340, you need an external debugger or an onboard debugging chip.

Divya_uni_ulm said:

 I have understood that there are 2 possible ways where I can flash the desired code.

Yes, using a Jlink external debugger, or a debugging chip from a DK (you could for instance connect an nRF5340 to the thingy:53 to program it). Using TF lite micro is a way to get functioning code that you could potentially use on an SoC or MCU, but not something you can use to program/flash it.

Divya_uni_ulm said:

Is there any link/document/blog related to programming microcontrollers using Tensorflow Lite Micro?

Nothing besides what I've already provided you unfortunately. 

Divya_uni_ulm said:

As mentioned in the link, it is a little bit confusing for me but can we use this method only with SDK, or can we also program Thingy:53 with sample code to test and check the behavior?

I am a bit uncertain about what you mean here. Note that when people in the thread you linked to (as well as people on devzone) say SDK they often use it as a shorthand for the nRF5 SDK (while NCS is also in fact an SDK). Though a DK is not an SDK.

Divya_uni_ulm said:

Though I have understood that programming with the debugger or nRF5340DK board is one way to solve this issue but do you think we can use TF lite Micro to program Thingy:53, as well?

Like I've alluded to above, I think you are confusing things.

Regards,

Elfving

[Divya_uni_ulm]

Hello Elfving,

As mentioned in your first answer I have used the Jlink programmer to program a sample on my device.

To check the functionality of Thingy I have used Bluetooth: Peripheral LBS sample code to check the functionality and I have followed the steps mentioned here:

https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/peripheral_lbs/README.html

I am using ios phone to check the functionality but somehow I am not able to check the behavior from step 5 onwards. Also, I am using visual studio to build the device and code.

So, my question is :

1. Is there any other way to check if it is working correctly or not?
2. Also, I have noticed that there are many print commands in the sample code but when I am testing the sample I can not find any print command on the terminal. So, is there any way if I can see these print commands on the terminal, and then I can check where my code is throwing the error?
3. My whole purpose is to test the sample for now and check if it is working perfectly or not and then try with my own code. So, in both the cases I need to print and check the messages to verify the error/state of my code

Please help me to resolve this issue.

Regards,

Divya

[Elfving]

Hello Divya!

I see.

So these print commands, along with just basic information like "Zephyr starting up" should get printed on the COM port. To read that you need a serial terminal, eg. the one you get with the VSC extention, or something like Putty. Are you using any of those? And if so, are you finding the COM port that is used by the Thingy:53?

Regards,

Elfving