No output to UART console when CONFIG_BT=y

[jchan12345]

There is no output to UART console when I set CONFIG_BT=y in prj.conf

peripheral_lbs sample project in ncs V2.0.2 can't printk anything.  

[Hieu]

Hi,

Unfortunately I cannot reproduce your issue.
I just now tried a brand new application based on the NCS v2.0.2 peripheral_lbs example on both the nRF52DK and the nRF5340DK, and for both printk() worked and I got data on a Serial Port.
I really don't think CONFIG_BT=y would break UART console, that would really not make sense.

Are you developing on a Development Kit or on your custom board?

By the way, as you requested, the prj.conf used to test:

#
# Copyright (c) 2018 Nordic Semiconductor
#
# SPDX-License-Identifier: LicenseRef-Nordic-5-Clause
#
CONFIG_NCS_SAMPLES_DEFAULTS=y

CONFIG_BT=y
CONFIG_BT_PERIPHERAL=y
CONFIG_BT_DEVICE_NAME="Nordic_LBS"

# Enable the LBS service
CONFIG_BT_LBS=y
CONFIG_BT_LBS_POLL_BUTTON=y
CONFIG_DK_LIBRARY=y

CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=2048

Best regards,
Hieu

[jchan12345]

Hello Hieu, 

Thanks for your quick response.  I have one more request.  Would you use the nrf5340dk_nrf5340_cpuapp.overlay    file to disable to UART console and see if you can still receive output.?  My problem seems to be complicated.  The UART on nRF5340DK always work even if I intentionally disable the UART or assign different TX and RX pins.   I am trying to make sure the overlay file can change the behavior first, then I will make correct adjustment on my own custom board. 

I have more problem on my custom board, but one thing at a time.  I want to get the UART working in different configuration/overlay first.

Thanks again.

My own. nrf5340dk_nrf5340_cpuapp.overlay. for a different custom board, but nRF5340DK is unexpectly working fine with it, so something is wrong

I may have mistakes in the overlay file

&uart0 {
    //status = "okay";
    status = "disabled";
	label = "UART_0";
	current-speed = <115200>;		// 115200
    pinctrl-0 = <&uart0_default_alt>;
    pinctrl-1 = <&uart0_sleep_alt>;
    pinctrl-names = "default", "sleep";
};


&pinctrl {
    uart0_default_alt: uart0_default_alt {
        group1 {
            psels = <NRF_PSEL(UART_TX, 1, 1)>;		// P1.1 is TX
        };
        group2 {
            psels = <NRF_PSEL(UART_RX, 0, 29)>;		// P0.29 is RX
            bias-pull-up;
        };
    };
    uart0_sleep_alt: uart0_sleep_alt {
        group1 {
            psels = <NRF_PSEL(UART_TX, 1, 1)>,		// P1.1 is TX
                    <NRF_PSEL(UART_RX, 0, 29)>;		// P0.29 is RX
            low-power-enable;
        };
    };
};

[jchan12345]

The message *** Booting Zephyr OS build v3.1.99-ncs1 *** coming out at 

• TX at P1.01
• RX at P0.29

is actually from the NetCore.   I got the output of AppCore using RTT, so my application is running fine.  It is just somehow the UART pins of NetCore  are connected as specified in the overlay file for AppCore!!!!

I will need your guidance to re-route the AppCore UART to 

• TX at P1.01
• RX at P0.29

so I don't need to use RTT for it.

Anyway, it is interesting that the UART of NetCore is actually mapped to that for the NetCore.   However, it is better to document it and print messages from AppCore and NetCore.   Both print the same message*** Booting Zephyr OS build v3.1.99-ncs1 ***  at the beginning.  Hard to tell if it has been re routed.

Thanks for your great help!!!

[jchan12345]

Let me clarify.  I am able to use my custom board RTT for the AppCore with 

CONFIG_SERIAL=n

CONFIG_USE_SEGGER_RTT=y

CONFIG_RTT_CONSOLE=y

CONFIG_UART_CONSOLE=n

in prj.conf

and I got some blue tooth messages from the AppCore

Starting Zombie Bluetooth Peripheral LBS example
I: 2 Sectors of 4096 bytes
I: alloc wra: 0, fd0
I: data wra: 0, 1c
I: No ID address. App must call settings_load()
Bluetooth initialized
Advertising successfully started

and I got *** Booting Zephyr OS build v3.1.99-ncs1  *** from UART with 

• TX at P1.01
• RX at P0.29

What I need is to flip the RTT and  UART.   With AppCore messages come out from UART and NetCore messages come out from RTT.

My custom board has only one UART, so I use it for the AppCore with shell commands.

Need to re-route with different configuration.

Thanks for helping.

JC

[jchan12345]

By setting 

CONFIG_SERIAL=y or n in child_image/hci_rpmsg.conf 

I can see or not see *** Booting Zephyr OS build v3.1.99-ncs1 ***. on the UART console connected to my custom board running application built with overlay file nrf5340dk_nrf5340_cuppapp.overlay setting 

• TX at P1.01
• RX at P0.29

The important point is I am using overlay file for AppCore to configure the UART pins but turning on/off tx/rx data with CONFIG_SERIAL for child image which is running in the NetCore!!!!

This is the reason that I think the message *** Booting Zephyr OS build v3.1.99-ncs1 *** on my console connected to the AppCore UART is actually the bootup message from the NetCore.

Now, I can disable the NetCore UART

The next step is to configure AppCore UART to

• TX at P1.01
• RX at P0.29

Do you have any suggestion.   Thanks for your help.

 

[jchan12345]

With CONFIG_SERIAL=n in child_image/hci_rpmsg.conf, I can shut down the UART of NetCore, but setting. 

CONFIG_UART_CONSOLE=y

CONFIG_SERIAL=y

in the prj.conf does not send any bootup message from the AppCore to 

• TX at P1.01
• RX at P0.29

[jchan12345]

Hell Hieu,

Beside working on my custom board, I also try to learn and compare with the nRF5340DK board.  To start with a new peripheral_lbs project with NCS V2.1.0.  I got the following warning when creating it with nRF Connect SDK

warning: UART_CONSOLE (defined at drivers/console/Kconfig:43) was assigned the value 'y' but got the
value 'n'. Check these unsatisfied dependencies: SERIAL (=n), SERIAL_HAS_DRIVER (=n). See
docs.zephyrproject.org/.../kconfig.html and/or look up UART_CONSOLE in
the menuconfig/guiconfig interface. The Application Development Primer, Setting Configuration
Values, and Kconfig - Tips and Best Practices sections of the manual might be helpful too.

Just following very lead related to UART like old fashion detective work.

Did you see this warning when creating the application?

Thanks,

JC

[jchan12345]

Never mind.  The warning: UART_CONSOLE (defined at drivers/console/Kconfig:43) was assigned the value 'y' but got the value 'n'.

is related to 

CONFIG_SERIAL=n

in hci_rpmsg.conf