Bluetooth mesh sensor client example gives different outputs in different mobile devices

[SaSu]

Hello

I tried bluetooth mesh sensor server and client example, everything is good including provisioning process in mobile but the output is different with different mobiles. i have 2 mobiles where i tested in both mobiles i get output of this part as shown in picture-1

picture-1

and

picture-2

and from the picture-2 of code except chip temperature i can see other printk functions in output.

I tried this in my colleague mobile in that i can see picture-2 outputs but not picture-1 output.

I am really confused, why this happens? Can anyone help me as soon as possible please...

Regards

SaSu

[AHaug]

Hi,

1. Which devices did you use for the sensor server and client samples?
2. Could you add the output you see on your mobiles as well? 
3. Are there any differences between the mobiles? Different OS'?

Kind regards,
Andreas

[SaSu]

Hello

Sorry for late response. 1. For sensor_server thingy:53 with nRF5340DK and for sensor_client nRF52840DK

2. From my colleague mobile i dont have screenshot also he is not available now its android and output comes from picture-2 i.e "chip temperature is .. ", "presence detected" and so on. I have two mobiles one is android and other is IOS so in both i could not see "chip temperature" output line its directly jumping to picture-1 i.e "Relative runtime in 0 to 30 degrees : 0.0000 percent" and also i can see presence detected lines when i press button on thingy-53.

3. Already answered in point 2

Regards

[SaSu]

It is triggering and sensor->id is not equal to bt_mesh_sensor_present_dev_op_temp.id.

Here are the screenshots for that. And i want the bt_mesh_sensor_present_dev_op_temp.id same as sensor->id. What should i do?

Regards

[Edvin]

Ok, so the issue is not that printk() is not working. The issue is that it never enters the condition:

else if (sensor->id == bt_mesh_sensor_presence_detected.id)

I am not that familiar with the sensor_cli API. But apparently, you are triggering the callback with sensor->id == bt_mesh_sensor_time_since_presence_detected.id. How do you trigger this?

[SaSu]

sensor->id == bt_mesh_sensor_time_since_presence_detected.id this is triggering when button is pressed on thingy-53. I need the solution for my problem (i.e., bt_mesh_sensor_present_dev_op_temp.id should be same as sensor->id). I am really waiting for the answer, its been so many days i posted this and its really very important to me.

Thank You and Regards

[Edvin]

Hello SaSu,

Remember that I don't know much about your application. What is the application flow from when you press the button on the thingy until the callback is triggered? Is it the same thingy that is running the application that produced the logs that you sent? Or does the Thingy send some message over Mesh to the device that printed the logs?

[SaSu]

It is the same thingy that sending the logs(eg: 4 seconds since presence detected when i pressed button on thingy)

FYI: Since you told you have no idea about my application it is the sample mesh program which is in nordic developer website(Mesh_Sensor and Mesh_Client) and i did not change anything also followed the same steps for provisioning process in the app too.

[Edvin]

Hello,

If you program the default, unmodified example to a DK, without provissioning it, What does the log look like? Mine looks like this:

Is that not the case for you?

I know it says that it is getting an error, but that is only because it is not provisioned that it returns:

#define EADDRNOTAVAIL 125 /**< Can't assign requested address */

Best regards,

Edvin

[SaSu]

Hi

I am getting like this.

So, what should i do now?

Regards

[SaSu]

Hello Edvin

I am still waiting for your reply for the next step as i already told its very important to me. Hope you understand.

Thank You

Regards

[Edvin]

Hello,

I understand, but I am missing quite a few steps of understanding. What happens between you pressing the button on the thingy and you end up in the sensor_cli_data_cb()? Can you please try to set a breakpoint there to check the callstack? Where is the sensor->id being set? 

Are you using the sample as it is descibred in the sample description? You have one node acting as a server and one as a client? The sensor_cli_data_cb() is triggered on the client, right? 

I needed to try the sample that you are talking about, and I want to clear up a few things:

The thingy is programmed with the sensor_server sample, not the sensor_client sample, right?

Edvin said:

Is it the same thingy that is running the application that produced the logs that you sent? Or does the Thingy send some message over Mesh to the device that printed the logs?

SaSu said:

It is the same thingy that sending the logs(eg: 4 seconds since presence detected when i pressed button on thingy)

And the logs are coming from a separate device in the same network? So the callback is not a button handler. It is a callback handler from the sensor. 

I need to leave the office now. I will be back on Monday. But you need to look into the implementation. Where in the sensor server is it triggering the message that triggers the callback in the sensor_client that prints the "presence detected" message. Because by default, it is not set up to send the temperature data. Alternatively, you can figure out how it prints the.

65.000000 second(s) since last presence detected
Relative runtime in 0 to 20 degrees: 0.000000 percent
Relative runtime in 20 to 25 degrees: 0.000000 percent
Relative runtime in 25 to 30 degrees: 100.000000 percent
Relative runtime in 30 to 100 degrees: 0.000000 percent
71.000000 second(s) since last presence detected

Where it gathers the temperature data from. You should be able to find that. 

Best regards,

Edvin

[SaSu]

Edvin said:

pressing the button on the thingy and you end up in the sensor_cli_data_cb()?

Yes it goes to  

else if (sensor->id ==
		   bt_mesh_sensor_time_since_presence_detected.id) {
		if (value->val1) {
			printk("%s second(s) since last presence detected\n",
			       bt_mesh_sensor_ch_str(value));
		} else {
			printk("No presence detected, or under 1 second since presence detected\n");
		}

Already "No Presence detecte, or.....") will be printing and when i press "%s second(s) since last presence detected" will print as follows

Edvin said:

Can you please try to set a breakpoint there to check the callstack?

Could not understand this, I could set break point as far as i know it really doesn't do anything just building process will stop till there(FYI: I doesn't get any errors in building process) and what is call stack and how can i check it? if you mean something different than what i understood.

Edvin said:

Where is the sensor->id being set?

Its sending to sensor_cli_data_cb() but bt_mesh_sensor_present_dev_op_temp.id and bt_mesh_sensor_presence_detected.id id's are getting different don't know why. and sensor->id ==bt_mesh_sensor_time_since_presence_detected.id these id's are same that's why when we press or don' press that part is being printed.

Edvin said:

Are you using the sample as it is descibred in the sample description? You have one node acting as a server and one as a client? The sensor_cli_data_cb() is triggered on the client, right? 

Yes, i am using the sample described in the sample description. Yes one node is server(i am using thing 53 with nRF5320_DK as server) and one node is client(i am using nRF42840_DK as client). Yes sensor_cli_data_cb() is triggering but only one if else part i.e as explained in above line.

Edvin said:

The thingy is programmed with the sensor_server sample, not the sensor_client sample, right?

Yes, it is programmed in sensor_server not in sensor_client thats why i get some output right otherwise i will get some issues or errors.

and FYI: everything is perfect with the sample program except

this part is not triggering because bt_mesh_sensor_present_dev_op_temp.id and bt_mesh_sensor_presence_detected.id id's are different.

Edvin said:

And the logs are coming from a separate device in the same network? So the callback is not a button handler. It is a callback handler from the sensor. 

Logs are coming from sensor_client with me its COM10 which i can see on PuTTY and those are being sent from sensor_server as it is a mesh sample example.

Edvin said:

Where in the sensor server is it triggering the message that triggers the callback in the sensor_client that prints the "presence detected" message. Because by default, it is not set up to send the temperature data. Alternatively, you can figure out how it prints the.

I know from where it is sending the messages.

from sensor_server from below part it is sending

and from sensor_client

here it receives. as you can see we use sensor types and as far as i figured that is main function to send and receive messages .

(FYI: You please check the sample program and run by yourself and update me whether you get the "chip temperature" output or not. Because i checked with 3 mobiles and its same problem and you check it once, if its working please tell me what different you have done and if it is not please check it what is the problem because you are expert than me as i am student, i am really not able to figure out what is the problem as the id's are auto generated and its not user given values. I am literally trying since 2 months as i couldn't figure out i updated a forum question a month ago. I am really waiting for answer. Hope you understand).

Thank You

Best Regards