• State Verified Answer
  • Replies 5 replies
  • Subscribers 74 subscribers
  • Views 1250 views
  • Users 0 members are here
Attachments (0)
Nordic Case Info
  • Case ID: 300473
Options

nRF52840 dongle transmit power and bandwidth for thread network.

Sohaib

I have developed a thread network using nRF52840 dongle and Raspberry Pi 4B. I have checked from the command line of the RPi, the transmit power is 0dBm. Can you please confirm if we can increase this transmit power from the command line, most importantly, what would be the range of communication for 15.4 thread with this hardware setup. Additionally if I can get some information about the receiver sensitivity (min RSSI).

Secondly, what is the channel bandwidth for this thread transmission on nRF52 dongle, If you could please share some documentation regarding this that would be also great.  

Parents
  • 0

    Thirdly, what are the multiplexing/multiple access/modulation techniques used. 

    Thank you. 

  • 0 in reply to Sohaib

    Hello,

    Sorry for the short reply, but we are a bit short staffed due to Holiday Seasons. Sorry for the incovenience. We will be back to normal operation in January. 

    Regarding setting the TX power, please see my reply in this ticket:

    I don't know if this has changed since I wrote the replies in that ticket, but at least it should hold some pointers on where to look.

    most importantly, what would be the range of communication for 15.4 thread with this hardware setup.

    We usually give out exact numbers for this. If I told you it is 10 meters, and it turns out to be shorter in your tests, you would blame me. If I said it was 1 meter, and you are in a really noisy environment that may not even work. It always depends on the surroundings (clear line of sight or not. If not, what are the obstacles made of?). It also heavily depends on the traffic on air. Both WiFi and Bluetooth are using the same frequencies, and noise from that will affect the quality of the received signal strength. 

    Secondly, what is the channel bandwidth for this thread transmission on nRF52 dongle,

    I don't have this from the top of my head. I guess you will be able to find answers for this by searching for channel bandwidth on 802.15.4, but that as well will decrease with the amount of noise in the environment.

    Sohaib said:
    Thirdly, what are the multiplexing/multiple access/modulation techniques used

    This is also defined by 802.15.4. It is some sort of listen before talk, meaning it will measure the noise level on the channel before it attempts to transmit. This also affects question two. If there are a lot of nodes in your network already, then this will lower the throghput for the other nodes, depending on how much traffic they generate. 

    Please note that we are very short staffed due to Holiday Seasons. I am sorry for the inconvenience. We will be back with normal operations in January. 

    Best regards,

    Edvin

Reply
  • 0 in reply to Sohaib

    Hello,

    Sorry for the short reply, but we are a bit short staffed due to Holiday Seasons. Sorry for the incovenience. We will be back to normal operation in January. 

    Regarding setting the TX power, please see my reply in this ticket:

    I don't know if this has changed since I wrote the replies in that ticket, but at least it should hold some pointers on where to look.

    most importantly, what would be the range of communication for 15.4 thread with this hardware setup.

    We usually give out exact numbers for this. If I told you it is 10 meters, and it turns out to be shorter in your tests, you would blame me. If I said it was 1 meter, and you are in a really noisy environment that may not even work. It always depends on the surroundings (clear line of sight or not. If not, what are the obstacles made of?). It also heavily depends on the traffic on air. Both WiFi and Bluetooth are using the same frequencies, and noise from that will affect the quality of the received signal strength. 

    Secondly, what is the channel bandwidth for this thread transmission on nRF52 dongle,

    I don't have this from the top of my head. I guess you will be able to find answers for this by searching for channel bandwidth on 802.15.4, but that as well will decrease with the amount of noise in the environment.

    Sohaib said:
    Thirdly, what are the multiplexing/multiple access/modulation techniques used

    This is also defined by 802.15.4. It is some sort of listen before talk, meaning it will measure the noise level on the channel before it attempts to transmit. This also affects question two. If there are a lot of nodes in your network already, then this will lower the throghput for the other nodes, depending on how much traffic they generate. 

    Please note that we are very short staffed due to Holiday Seasons. I am sorry for the inconvenience. We will be back with normal operations in January. 

    Best regards,

    Edvin

Children
Related
Terms of service