Error when building Modem_Shell for Thingy91 -> ld.bfd: region `FLASH' overflowed by 64612 bytes

[xr47]

When I execute the command:  west build -p -b thingy91_nrf9160_ns -- -DDTC_OVERLAY_FILE=ppp.overlay -DOVERLAY_CONFIG=overlay-ppp.conf

I get: 

ld.bfd: region `FLASH' overflowed by 64612 bytes
collect2: error: ld returned 1 exit status
ninja: build stopped: subcommand failed.
FATAL ERROR: command exited with status 1: /usr/local/bin/cmake --build /home/xavier/ncs/v2.2.99-dev3/nrf/samples/nrf9160/modem_shell/build

I only wish to use the modem shell for the PPP functionality, and do not care about including support that is not necessary to achieve PPP dial up service. Any suggestions on how to build this image with only PPP that will fit on the Thingy91 would be IMMENSELY appreciated!   

[Øyvind]

Hello, 

Could you please test with latest tagged version v2.2.0? You are currently on the main branch. The nRF Connect SDK repository is described in our documentation. As stated, the main branch can often be unstable as this is where the latest development is added. The tagged versions are stable versions. 

Are you able to share more information about you setup and environment?  I tested on my side on Linux, MacOS, and Windows, the latter using VS Code. extension. The former two built with success, however, with Windows I got the same issue. I updated the SDK and Toolchain, and it successfully built.

Can you test on your side?

Kind regards,
Øyvind

[xr47]

I managed to trim fat from the the image by tweaking the config files and had a successful build and flash for the Thingy91 by enabling only CONFIG_MOSH_LINK=y in prj.conf, and CONFIG_MOSH_PPP=y. in the overlay-ppp.conf files.

Now, when I connect to the device via serial monitor, it outputs garbage every second or so.

ie, ~�}#�!}!}(} }(}!}$}%�6m~~�}#�!}!}(} }(}!}$}%�6m~

Have you tested PPP service with a Thingy91 before? All I did was disable support for everything but PPP and now the modem shell is broken. If I build an image with the exact same prj.conf but don't include the cmake options for PPP, the application works just fine and no garbage is output to the terminal. I'm out of ideas.

[Marshall]

That "garbage" is the PPP session...

[xr47]

I am simply following these directions: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/nrf9160/modem_shell/README.html#ppp-support 

Any insight on what would be causing the PPP session to output nonsense and disallow me to interact with the modem shell?

[Marshall]

I think from memory there is an option to redirect the PPP out another port.

# UARTs are switched

CONFIG_NET_PPP_UART_NAME="UART_0"

If you connect your PI to this "garbage" and set a PPP session, it should just magically work. 

Try the script with the noccp option. ([Regression ncs v1.8.0] nRF9160-DK , Modem_shell demo , HARD FAULT after connecting over ppp - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)_

 i.e. this is the command that worked for us. 

sudo pppd /dev/ttyUSB0 115200 nocrtscts debug nodetach noauth local noccp

[xr47]

Where would that CONFIG_NET_PPP... need to go? I tried adding it to the overlay-ppp.conf and then received a bunch of errors. I was able to set a PPP session with the command you provided but I'm not able to access the internet, so I've got some digging to do.

[Marshall]

I Had mine in overlay-ppp.conf - take a look at KConfig, there might be some dependencies. 

[xr47]

I didn't need to do anything apparently. The issue resolved itself after a few minutes. Thanks for all the help!!!!