nrf9160 AT-command Error

[_bhanu]

Hi,

we have designed nrf9160 custom boards.

i have upload he AT_CLIENT example but i'm not able to get response when i send commands. total i have 2 custom board but i one custom board its working but in another board its not working. Both design are same but i have noticed the nrf9160 chips is different

.

the device which have N symbol in that AT commands are working fine, but the device which have UK in that only AT response is working other then that any commands not getting ok response  i have sent AT+CFUN? but im getting response ERROR, Expect AT other commands are getting response ERROR

Thank you

[Øyvind]

Hello, 

have you had a design review of your custom design? What revisions of the nRF9160 are you using on your boards, from the image it is difficult to read anything.

Kind regards,
Øyvind 

[_bhanu]

Hi Oyvind,

Øyvind said:

What revisions of the nRF9160 are you using on your boards, from the image it is difficult to read anything.

Please look into the below image. In that which have Nordic symbol that device is working fine when in send AT commands  but another one is giving always Error response when in send AT commands, and here both board designs are same.

please check why another nrf9160 chip not giving OK response 

let me know if you need any information 

Thank you

[Øyvind]

_bhanu said:

But after upgrade to (mfw_nrf9160_1.3.4) device UART port is not showing

How do you configure the UART ports in your project? How do you connect to your device from the computer? What happens if you use mfw_nrf9160_1.3.2, same as the other device?

[_bhanu]

Hi,

Øyvind said:

How do you configure the UART ports in your project?

using uart0 port and TX & RX pins are connected to FTDI. 

Øyvind said:

How do you connect to your device from the computer?

Through USB cable we are connecting FTDI to my cumputer.

Øyvind said:

What happens if you use mfw_nrf9160_1.3.2,

In one device as you said we upgrade firmware mwf_pti_nrf9160_1.1.5 to mwf_nrf9160_1.3.4 after that usb port was not detected in  link_monitor. we dont no why but usb port show in other serial monitor application like(ardunio,tera term).

we have another device which have mwf_nrf9160_1.3.2 in that device usb port showing in link_monitor  our both devices have same design.

Below mwf_nrf9160_1.3.2 version showing in link_monitor why mwf_nrf9160_1.3.4 version device not showing in link_mother?

[Håkon Alseth]

Hi,

 

_bhanu said:

Below mwf_nrf9160_1.3.2 version showing in link_monitor why mwf_nrf9160_1.3.4 version device not showing in link_mother?

at_client shall work with both of these mfw versions.

Can you share any logs or similar? Have you tried reprogramming the device in-question?

 

Kind regards,

Håkon

[_bhanu]

Hi

Håkon Alseth said:

Can you share any logs or similar? Have you tried reprogramming the device in-question?

to see logs first it have to show the device port but its not showing  port in lte_link_monitor.

but when use  mwf_nrf9160_1.3.2  it showng device port But when i use mwf_nrf9160_1.3.4   its not even showing the device port.

Thanks 

[Håkon Alseth]

Hi,

 

_bhanu said:

But when i use mwf_nrf9160_1.3.4   its not even showing the device port.

What do you mean specifically with "device port" ? Do you mean the USB-uart adapter?

If yes; this is a external component and should not have any effect on the nRF9160 at all.

 

Can you share screenshots or logs of what your issue is?

 

Kind regards,

Håkon

[_bhanu]

Hi,

Håkon Alseth said:

What do you mean specifically with "device port" ? Do you mean the USB-uart adapter?

yes  it is usb poart .

Håkon Alseth said:

Can you share screenshots or logs of what your issue is?

In this screenshot you have seen  usb0 port in arduino. but its not showing in lte_link_monitor 

in my device that usb is going to act like a uart0

[Håkon Alseth]

Hi,

 

Thank you for sharing this.

You can use any terminal you'd like to send AT commands.

For other ports to be detected in LTE Link Monitor, you have to ensure that the "Show only supported devices" is left unchecked:

Then it should appear in the list:

 

Kind regards,

Håkon