I can't control LED belt

I am using nrf52832 and developing with FreeRTOS. I want to use Bluetooth and control a WS2812 LED strip simultaneously. When I don't start Bluetooth, i.e. //nrf_sdh_freertos_init(advertising_start, &erase_bonds), I can control the LED strip normally. However, when I start Bluetooth, the LED strip control becomes abnormal.

Parents Reply Children
  • I was use hardware timer to control ws2812.

    uint32_t led_hardware_timer_init(void)
    {
    	uint32_t err_code = NRF_SUCCESS;
    	
    	nrf_drv_timer_config_t timer_config;
    	timer_config.frequency = NRF_TIMER_FREQ_62500Hz;
    	timer_config.mode = NRF_TIMER_MODE_TIMER;
    	timer_config.bit_width = NRF_TIMER_BIT_WIDTH_24;
    	timer_config.interrupt_priority = APP_IRQ_PRIORITY_HIGHEST;
    	timer_config.p_context = NULL;
    	
    	err_code = nrf_drv_timer_init(&led_timer, &timer_config, led_timeout_handler);
        
        if(NRF_SUCCESS == err_code)
    	{
            m_led_timer_state = TIMER_STATE_INITIALIZED;
    	}
    	
    	return err_code;
    }

  • Hi Suhaihui, 

    I don't think using the hardware timer can be tricky when using with FreeRTOS. 
    How long do you stay in the interrupt handler ? Have you tried to test with APP_IRQ_PRIORITY_LOW ? 
    Which timer do you use ? Please be aware that TIMER0 is blocked by the softdevice and you should choose other TIMER.

  • 1. I was used timer1
       ie: NRF_DRV_TIMER_INSTANCE(1)
    2.  I tried to test with APP_IRQ_PRIORITY_LOW
       same result

    3. It stay in interrupt less then 0.5ms

    I control ws2812 like this

    #define   RGB_H      (NRF_GPIO->OUTSET = (1UL << TARGET_LED1_PIN))   
    #define   RGB_L      (NRF_GPIO->OUTCLR = (1UL << TARGET_LED1_PIN))  
    
    static void LED_Write0(void)
    {
    	RGB_H;
    	__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();
    	__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();
    	RGB_L;
    	__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();
    	__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();
        __NOP();
    }
    
    static void LED_Write1(void)
    {
    	RGB_H;
    	__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();
    	__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();
        __NOP();__NOP();__NOP();__NOP();__NOP();
        __NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();
    	__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();__NOP();
    	
    	RGB_L;
    	__NOP();__NOP();__NOP();
    }

  • Hi, 
    Please show the full code how you call LED_Write0 and LED_Write1.
    Have you looked at how we use timer in the ble_app_hrs_freertos example ? 

Related