NRF52840 nrf nrfx PWM glitching complex waveform

[nick_bike]

I need to create some complex waveforms and my strategy is to use nrfx_pwm_complex_playback to play one waveform then the other as a seamless loop; and I'll manipulate the sequence that's not currently being played and it should then switch in at the end of the current sequence.

I've set up the most simple case with two sequences. It's looping but the waveform is not good - single pulses popping up. This isn't finished code but should be complete.

What am I missing? Thanks!

static nrf_pwm_values_common_t sequence_data[ 2 ][ 100 ];

static nrf_pwm_sequence_t sequences[ 2 ];

static nrfx_pwm_config_t const config_motor =
{
.output_pins =
{
IO_PIN_MOTOR_PWM, // channel 0
NRFX_PWM_PIN_NOT_USED, // channel 1
NRFX_PWM_PIN_NOT_USED, // channel 2
NRFX_PWM_PIN_NOT_USED // channel 3
},
.irq_priority = 5,
.base_clock = NRF_PWM_CLK_8MHz, // Originally 8MHz
//.base_clock = NRF_PWM_CLK_1MHz, // Originally 8MHz
//.base_clock = NRF_PWM_CLK_125kHz,
.count_mode = NRF_PWM_MODE_UP,
//.top_value = 2500,
.top_value = 255,
.load_mode = NRF_PWM_LOAD_COMMON,
.step_mode = NRF_PWM_STEP_AUTO
};

  nrfx_pwm_init(&pwm_motor, &config_motor, NULL, NULL);

void io_spwm_motor_complex_flat( uint8_t seqIndex , uint32_t duty , uint16_t periods ) {
duty = 255 - duty;

sequence_data[ seqIndex ][ 0 ] = (duty <= 255 ) ? duty : 255 ;

sequences[ seqIndex ] = ( nrf_pwm_sequence_t )
{
.values.p_common = sequence_data[ seqIndex ],
.length = 1,
.repeats = periods,
.end_delay = 0
};
nrfx_pwm_sequence_update( &pwm_motor , seqIndex , &sequences[ seqIndex ] );
}

void io_spwm_complex_restart(uint32_t duty )
{
io_spwm_motor_complex_flat( 0 , 64 , 4 );
io_spwm_motor_complex_flat( 1 , 250 , 4 );

(void)nrfx_pwm_complex_playback(&pwm_motor, &sequences[ 0 ] , &sequences[ 1 ] , 2 , NRFX_PWM_FLAG_LOOP );

//(void)nrfx_pwm_simple_playback(&pwm_motor, &sequences[ 1 ] , 1, NRFX_PWM_FLAG_LOOP);

}

io_spwm_complex_restart( 1 );

[ovrebekk]

Hi Nick

I don't quite understand which pulses you are talking about by looking at the figure. 

If I understand your code correctly the PWM switches between 64/255, which are the short pulses, and 250/255, which is the other state where it is mostly high but will drop down shortly for each PWM period. 

To me the diagram looks OK, but maybe it is something I am missing?

If you can share your code as a C file I can also try to reproduce the issue here. 

Best regards
Torbjørn

[nick_bike]

Thank you. My intention with this code is that each sequence is 5 periods long (1+4). From the trace picture, you see that solo pulses appear which should not be there. The code above I think it enough to replicate the problem, there is no other code manipulating this device.

You see at nrfx_pwm_complex_playback, I have set loop to 2. If I set it to 1 this does not appear to play back the sequences properly even once; I get 5 x 64/255 pulses and one 250/255, looping. From the docs I think 1 is the correct value. It is as though the .repeats attribute is ignored and the value played only once.