Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
Hi, On the nrf54L15 with MCU boot enabled, what is approximately the fastest time that the chip could boot and set a gpio line high, if everything not critical is disabled...
i have the nrf5833 dk board, i just started programming from quick start and it worked two times and now it does not program at all, programming failed
I'm seeing garbled/malformed UART console output when running apps on the Thingy:91 X. This includes pre-built apps from Nordic and custom apps I build myself.
Here's an...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hello,
Brand new bluetooth 5 standard allows to create data packets up to 255 octets.
So, does maximum size of advertising data in Nordic devices comaptible to bluetooth...
Hello, when using sd_ble_gatts_hvx(), I keep getting 0x3401 error. I googled it and it appears that it's because I might not have the notification enabled.
But I very much...
OK. Weird question. I know, but that's only because I'm in the middle of a large program that I'm reading, believe me, I had done my fair share of homework and I understand...
I can't seem to get any of the UART examples for the NRF52 to compile on Eclipse. Eclipse is complaining that there are two definitions for uint8_t, one in _stdint.h and another...
Dear developers,
Currently, I am studying the new SDK 12.2. Now, I'm reading flash storage module. It seems very useful.
Just a question: While Persistent Storage module...
So it points to the ACTUAL value of a characteristic. So why do we need that function "ble_hvx_push()" (forgot its name, sorry, but you know what I mean) for? And what's with...
hi dear Engineers!
if I use sd_ble_gattc_primary_services_discover(..) with NULL last parameter , all SERVICES discovered OK:
start_handle=0x0001;
err_code = sd_ble_gattc_primary_services_discover...
We have a device which needs to survive dishwasher conditions. We believe most dishwashers operate up to 71C, but may reach 82C during 'sanitation' phase/drying.
This is...
Hi,
I'm using nRF5_SDK_12.2.0_f012efa and s132_nrf52_3.0.0_softdevice. We want to do the OTA on it. Before I add a DFU service to make it switch to bootloader, I have use...
Hello, I'm sending a series of data up to 7 bytes from an android phone, but I can only receive the first 5.
I'm asking what are the list of thing to mind if I were trying...
Hi,
I am trying to initiate Firmware Upgrade using the nRF Connect Mobile Application (also tried using nRF ToolBox).
As described in the below link -
github.com/.....
The footprint of sd_ble_gap_connect() is:
uint32_t, sd_ble_gap_connect(ble_gap_addr_t const *p_peer_addr, ble_gap_scan_params_t const *p_scan_params, ble_gap_conn_params_t...
This is what I believe, of course, my beliefs are flawed, so please DO point my errors out:
There is this attribute table on server/peripheral devices. The actual...
Hi，Nordic
I have one nRF24LU1P device, when I make it as USB Dongle, I will use :
hal_usb_endpoint_config(uint8_t ep_num, uint8_t ep_size, hal_usb_cb_endpoint_t endpoint_isr...
When I repeatedly (>290 times) send the same notification to the connected host via sd_ble_gatts_hvx, I get a sd_assertion:
Fault identifier: 0x1
Program counter: 0x104FA...
