I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Are there plans to release the files for download instead of online-only access through the Infocenter? It was always so nice to have them on-hand to grep in the previous...
When I try to compile DFU examples, I get the following errors :
"..\..\dfu_public_key.c(20): error: #35: #error directive: "Debug public key not valid for production...
I have my custom board wired to the nRF52 DK. Using the SAADC example code located in GitHub I am trying to set up SAADC to measure the coin cell battery that will power the...
I am sending and receiving streams of data over BLE.
Do I need to add a checksum byte for every GATT write/notification/indication to ensure that my data is not corrupt...
Hello All,
I am interfacing nRF905 as a receiver mode which are interface with nRF51 DK.
As a transmitter used this module www.alibaba.com/.../RF-100m-transmission-distance...
Hi,
I'm facing a little problem with custom service characteristic. I've set char settings as follows
attr_char_value.init_len = sizeof(uint8_t);
attr_char_value.init_offs...
Although this is easily fixable, Nordic engineers should be made aware that they made a minor change in SDKV12 that breaks makefiles on the Mac.
In /components/toolchain...
Hi,
I have downloaded the latest SDK12 for nRF52.
And i tried out the new "BLE Secure DFU Bootloader" example.
But i found that doing the BLE DFU with nrfutil on...
Hi,
I have nrf52 DK and sdk11.
I want to implement the time using internal RTC , the clock should run if the power is off ,i'm implementing in central code ,it has to...
Hi, I'm planning to add bluetooth LE support to my Arduino based project. I want to use nrf52832, but I couldn't find any example on Arduino interaction with this radio. I...
Hello. I have the need to get a device's unique address that remains stable across device firmware upgrades, etc.
Before SDKV12 I've been using sd_ble_gap_address_get(...
Hi
I want to know how to use ppi to wake up CPU from IDLE mode.
I've tried to use timer timeout event for triggering Port Event and wake up CPU, but can't assign NRF_GPIOTE...
I have been using a module of nRF52832. I write the Direct test mode in the module, to measure the current consumption of the Tx and Rx. DTM setting is + 4dBm, DCDC off. As...
Hello,
I try to send about 80kB of data between 2 beacons and I have encountered some problem that I got no idea how to resolve.
I have managed to connect devices, discover...