Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I have tested a sample code which sends some data through BLE in nRF52 development kit(PCA10400). The code is attached below.
nRF5_SDK_11.0.0_MPU6050_Acc_X_Output...
I'm trying to compile the bootloader_secure example for the 10040 dev board using make, and it appears the makefile was not updated correctly with the changes made to the...
Segger RTT viewer is a great debugging tool. But every time when I download new firmware into my board I have to close the viewer and then open it after download is finished...
Hi guys,
in my application, I'm trying to do multiple fota, I succeed at the first time & after that I can jump again to the bootloader, but after that something is going...
I used nRF51822 IC and SDK11 with softdevice S130. I found a problem that our product cannot work. I dumped the hex code of 2sets from 0x00000000 to 0x0003ffff. One can work...
Hi,
I am using the nRF51822 module. I am facing problem to send multiple data formats packets over nrf module. I am using nrf SDK 11 version.
I am attaching my code with...
I want to start developing a Bluetooth device with the NRF52 DK. For debugging and sniffing purposes to see what is going over the air, use the NRF51 dongle, get a NRF51 DK...
In the nRF52 specification, I cannot find figures for the interrupt latency for event on GPIO pins in different power mode OFF, ON (constant latency, Low Power).
Can you...
Hi. I need to use direct advertising option in my application to minimize the time needed to establish the connection.
Firstly, I set up the connection during "normal" fast...
Dear Nordic Team,
Thanks for supporting.
I am try to work multiple (Peripheral) tag ID read with one central and stored in my PC via UART communication. Which example...
Hi,
I am new to nRF microcontroller and communication . currently, I am working on nRF51822 microcontroller. I am able to communicate between two nRF51822 microcontrollers...
I am trying to modify make file of UART with make file of timer to give the functionality of UART and timer. I created the single code in main c file and added necessary source...
I have an application with my own custom service with a 128-bit UUID (including 4 characteristics). The application has worked so far. Now I try to add DFU service support...
hello all,
do you know if there is a way to disable code optimization only on some part of code?
I use optimization level 1 in Keil (otherwise the code does not fit...
