Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi
I have problem enabling gzll on my nRF51. Error diagnoses shows NRF_GZLL_ERROR_CODE_INTERNAL_ASSERT_OCCURRED (#15), every time I try to call nrf_gzll_enable();
Here is...
I've looked at the reference manual and the several forum questions asking the same question and do not understand the answers as they all seem to point to the same docs/original...
HI All,
We are using NRF52, S132 Softdevice , SDK 11.0.0.
In SPI DMA transfer, when we try to increase size of the m_tx_data greater than 254 bytes, it failed. It is working...
HI All,
I did all the things as in this post
devzone.nordicsemi.com/.../
But Whitelist is not working for me. My requirement is this, I need to add the first connected...
Hi everyone,
I must to program my device from nRFgo Studio (rel. 1.21). So I do this procedure:
I program the Softdevice (in my application S110 rel. 7.0.0);
I program...
I am using nrf51822 and I am trying to reduce the transmit range to 30 cm or less.Is it possible to achieve this. The reason I am doing this is that I will be working with...
Hi,
I want to use both SPI master & slave altogether, but when I include nrf_drv_spis.h upon compilation the following error occurs :
C:\Keil_v5\ARM\PACK\NordicSemiconductor...
I am trying to find out the lowest range of nrf51822 but so far I coulden't find anything. Most of the time people are trying to increase the range.Thanks.
Hi Guys.
I have compiled and programmed ble_app_uart program in to a nrf51DK (pca10028-nrf51488).
I downloaded and installed nRF UART V2.0 to android 5.1.1 .But while scanning...
Hi,all.i use pwm with sdk8.1 sample (SDK8.1\example\peripheral\pwm),my question is how to stop pwm and set the pin to low level? is my code correct?
my pwm init code:
...
I've a board with the nRF51 inside and a LIS3DH as accelerometer.
I already reflashed and I want to read the accelerometer values from the LIS3DH but I don't know where...
Hi Guys,
I tried to integrate the spi master project to ble_app_uart. For that I added the missing headers from spi project to ble_app_uart. And also I added the .c files...
Hi, Guys,
I am integrating the proximity app with dfu, everything else goes well. However, when I try to update bootloader through dfu, it failed. I check the MCP log,...
