I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hello,
I am using nrf51 SDK version 10.0.0 along with the nRF51822, and I believe I have found an issue with a macro that is supposed to check the correctness of a bit...
Hi All,
Another question for those out there much smarter than myself...
We're developing an application using nrf52, sdk11 and softdevice s132 2.0.0 and have been using...
I see it is advised not to just stop a timer, but to also shut it down for certain of the nRF52s. What call is necessary to achieve this since I understand it is deprecated...
I want to read the onboard (dev board) buttons which i believe are P13-P16. I want to know the working code.
uint32_t app_button_is_pushed ( uint8_t button_id,
bool *...
I am trying to estimate the memory usage of the s132 v3.0.0 running on a nRF52832. I am interested on acting only as a peripheral with one link at a time only. From app_ram_base...
Implementing my own protocol stack with low-level programming of the radio, can I broadcast by simply programming all units to receive the same address?
No addresses (such...
Hi,
I am trying to use the sdk version 9 for the NRF51 to take ADC samples and trasmit it over BLE over UART found in the link: github.com/.../nRF51-SDK-9-0-0
I downloaded...
For example,
CFLAGS += -DCONFIG_GPIO_AS_PINRESET
CFLAGS += -DNRF52_PAN_12
CFLAGS += -DBLE_STACK_SUPPORT_REQD
Where are -DCONFIG_GPIO_AS_PINRESET, -DNRF52_PAN_12...
Hi,
I faced a strange kind of issue while i was burning the same code on nrf51442 and nrf51882 chip. The code is running fine on the nrf51442 chip but the code wasn't running...
My µvision crashed during programming and will no longer respond to trying to program it. It boots into the bootloader mode. My computer sees it but the precompiled binaries...
Hi ,
I am using nRF51 SDK with S130 soft device lib, and it is running well when downloading the example of ble_app_uart. But when I want to modify the service UUID from...
Hi,
I'd like to check the battery level in my BLE device, and I can set a timer to handle the checking, however this means that Timer 1 would need to powered up, and hence...
Hi,
The situation: nRF51 has established a connection with the iOS/Android (custom made)App. The nRF51 goes out of the Bluetooth range. Eventually, the Bluetooth connection...
I have looked around but have been unable to find doc explaining this. If there's something around, I'd truly appreciate a pointer.
I have an existing (solar powered) device...
