nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi,
We are a group of students at NTNU looking at the possibility of creating a small device that connects to your phone and multiple other BT devices simultaneously, letting...
Hello,
This is a quick question regarding the behavior of the Power Supervisor POF warning. We implemented a fairly naive use of the POF warning where we would log an POF...
Hello I am using the NRF52832 in ESB mode. I use both VERIFY_SUCCESS() and APP_ERROR_CHECK() within my code in various places but when am I supposed to use versus the other...
i have project app_ble_uart and i want add to it functin read from mpu6050 i add to Makefile Makefile pathes and add #include "mpu6050.h" and InitMPU6050(0x68); into main...
Hi,
I am currently working to measure power consumption on a custom board and I found huge power consumption while advertising (BMD-300 1.15mA DCDC enabled).
So I have...
Hi,
I am trouble with private key generation in nrfutil. I am following the tutorial infocenter.nordicsemi.com/index.jsp.
When I am giving the command nrfutil keys generate...
Hi, do you have a central peripheral combo example which illustrates indication (not notification)?
Alternatively, if you could list the steps to change from notification...
It seems GPIOTE interrupt do not trigger when multiple IN signals are defined as GPIOTE_CONFIG_IN_SENSE_XXX(false).
It works when GPIOTE_CONFIG_IN_SENSE_XXX(true)
I am...
With SDK 14:
If I flash in this order:
softdevice_s132.hex
bootloader_secure_ble_debug_ with bonds_s132.hex
3. ble_app_buttonless_dfu with _bonds_s132_with_setting_page...
I am having issues to use 2nd UART. When I run Keil in debug mode it shows me three UART registers.
i) UART0
ii) UARTE0
iii) UARTE1
Is this UART0 and UARTE0 same thing...
I am using NRF51822 Rev3 and softdevice 7 in my project. On communication with
Android device sometimes the link disconnects with disconnection reason61(0x3D)
BLE_HCI_CONN_TERMINATED_DUE_TO_MIC_FAILURE...
I have used nrf24l01+(production year=2015) in my project and my board and my program are working well......but when I change nrf24l01+(production year=2016) my board doesn...
I have an application where knowledge of the current date/time is important. This is implemented by the central passing the time to the peripheral when it initially connects...
I am able to flash/program nrf51822 with openOCD on Raspberry-pi and STLink-v2
but when I invoke Open On-Chip Debugger on telnet to write on UICR register, it don't give...
