Hi,
We're evaluating NFC for our project.
I've been testing with a nRF52840DK - PCA10056 Version 3.0.2.
Using the antenna supplied with the Development Kit I am...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi everyone,
I am using nRF52832 chip and trying to use BLE on that. I flashed SoftDevice. When I flash the "ble_app_uart" example, error code 0x3001 occurs. the function...
I am using jlink to program the custom board. I was able to program the board earlier, but now this error is comming. I have rechecked the connection and it is fine.
The...
Hello all,
I am in the design stage of custom board for Automotive application using nrf51824. i have the below queries,
In the below link there are two reference...
If the DCDC is enabled in the nRF52832 and during operation one or both the external inductors is damaged what is the effect on the device? Will the power sub-system compensate...
Hi,
I can send and receive commands from nRF51 Dongle to nRF51822 via using nRF Connect UART over BLE Service.
My question is : Is there another way to reach nRF51 Dongle...
Hello,
I have chip nrf51822 connected to nrf51dk. An usb connection provides power to both chips. While checking power of both chips via nrf connect on iphone7 i discovered...
Connect establish with smartfone in peripherial mode. SDK13. S132. Periodic I observe disconnect, than 2-3 advertise packet and new connect again.
Where can I see what reason...
I have a little hobby project going on where I'm trying to make Nordic's old temperature broadcaster example work with the nRF52: github.com/.../
The project was originally...
As the product specification says,The HFCLK clock controller provides mang kinds clock to the system:
HCLK64M:64MHZ CPU clock
PCLK1M:1MHZ peripheral clock
PCLK16M:16MHZ...
Hello Folks,
I am currently try to program RedBear BLE nano board (which is essentially nrf51822) using Nordic SDK v12, which has features of secure OTA. However after...
I have started working on the external file access with NRF
is it possible to read or access the data from the external file into NRF programming
similar to what we do...
I am running a modified version of the app_uart_c example on a nRF52832 using softdevice 132.
I want to send a large hex number to the peripheral I'm connected to. Is it...
Hi,
No matter what I adjust, I can't get the PPK to output over 2.2V. I happen to be using an older nRF52 preview DK (figured it'd be a good use for that board now that it...
tl;dr: UART transmission sometimes stops and never resumes. Only a
power cycle resolves the issue; a system reset is not sufficient. The
problem only occurs when flow control...
