Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
I am getting an error of "undefined reference to `pm_state_force" .
Also, the output files, config file is not showing the command : CONFIG_PM =y
prj.conf file has : ...
Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
ble_app_gls_pca10056_s140.hex
Hi,
I am new in this field and i am trying to do current measurement on the nrf52840 PDK using PPK, in sleep mode(sd_power_system_off) i...
Hi,
I have just bought an nRFGo Motherboard (nRF6310) to develop for the nRF24LE1 (nRF2722). I was able to run some example code on the chip like toggling a pin. Next I...
Hello,
I have an application based on SDK 11 and Softdevice v2.0.0. Also there is a legacy bootloader from SDK 11 for performing DFU.
I am wondering whether it is possible...
When I run the UART app nRF5_SDK_12.3.0_d7731ad\examples\peripheral\uart in debug mode, the disassembly window opens, and I seem to get stuck on the second instruction. Step...
I am using a nRF52 and I have to measure two voltages:
the first continuously
when a command is received, the second voltage have to be measured and then...
Hi,
I flashed my nRF52840-PDK with UART/Serial Port Emulation over BLE program. Everything seems to be ok and I can connect with board via Android application. Next I would...
Hi!
I try to send data using advertise PDU and I need use custom 128 UUID.
How to convert to right format service_128_uuid and replace 16-bit value to init.advdata.p_service_data_array...
I'd like to use the nrf52832 as a mesh switch with battery powered. But I didn't find any sample code for the Low power feature in current mesh SDK v0.10.1. Does it support...
Hi,
Dear Nordic experts:
I encountered with a couple of *** issue while configuring SPI port on nRF52832 with PCA10040 demo board. Here I wrap up as below:
First...
I write NRF_UART0->ENABLE = 0x00 in my app in first line code, but now nrf51822 can connect but cannot Download and erase;
in keil it report:
**JLink Warning:...
Hi I am new to Nordic Development. I am developing a product that will use the Rigado BMD-300 module (nRF52832 but no need for FCC compliance testing). The evaluation board...
Hi to everyone!
I'm trying to use the nRF52832 board as master to use an external device (as slave) through SPI.
I take the example peripheral/SPI to start to learn how...
Hi,
How to set the length of the advertising device name? Even i set name type to BLE_ADVDATA_FULL_NAME, i can only able to set maximum of 14bytes. If i increase the name...
