Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
I use nrf51822 + S130 platform, in my application I used ADC,UART and APP TIMER, I mens only these can cause interruptions，all these interrupt priority is 3(APP_IRQ_PRIORITY_LOWEST...
Hey guys,
First of all, I'm using the SDK 14.1 with my nRF52832-DK.
I'm trying to get the function app_timer_start() work with the app_scheduler .
But the app_timer_start...
I'd like to buy a large amount of Nordic modules with Central and peripheral function with UART interface (similar to HM10 which is based on TI). The purpose is to build a...
Hi,
I just found, fds initialization sequence is important for fds_event_handler to be called.
My scenario:
nrf52832
SDK 12.2.0
MDK
My sequence to call fds...
How to solve problem with two (or more) simultaneously working devices with nrf52. I mean I have android app to connect to device. App is connecting to random device. I use...
Alright I'm a total newbie and have gotten myself so far...
I've compiled my project on macOS using ARM-GCC. Using the PCA10028 and the nRF51422, which works great on my...
I'm printing the value of the UUID of the service(s) discovered on two types devices when the BLE Multi-link Example connects to them, an NRF52 flashed with the blinky app...
Hi, I'm planning a project that uses MQTT with Raspberry Pi (RPi) 3 and PCA10040 (nRF52-DK).
I'm planning to use the AWS (Amazon Web Service) EC2 as a MQTT broker.
It...
Hello ,
I am using nrf52 Dk and nrf52832 custom board for testing ble communication. I am using ble_app_uart and ble_app_uart_c examples to test ble communication. In my...
Hey guys,
I'm using the SDK 14.0 on my nRF52832 with the SoftDevice 132, my IDE is Keil.
And I merged the ble_app_uart example with the ble_app_cts_c example and the...
Hi,
When I take a vanilla Objective C Xcode project and try to convert it to Cocoapods for an iOSDFULibrary with Xcode 9 results in an unopenable project. You get an error...
Hi,
I am using nrf52832 to scan beacons and then store temporary into two dimensional array.
I made interrupt that call after some interval to send stored beacons over...
Hello,
I got two device with DFU-OTA service enabled
(included device manager and dfu related handlers/files; merged the application, dual-bank bootloader, s130, app_valid_setting...
Using GCC compiler with Eclipse, sdk v14.1, nRF52832, in ESB protocol mode.
The code compiles and builds just fine, all links are ok, but the code below issues a syntax...
One of my nRF52-DK started to act oddly - very brief message in red type flashed up by nRFgoStudio on programming a few times - unfortunately too fast for me to read.
Now...
