Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
Is there a migration guide from 8.0.0 to 8.1.0? A lot has changed in GPIOTE and I can't make sense of it.
For example, should I be linking against app_gpiote.c , nrf_drv_gpiote...
I am new to BLE but have been reading up about it. My understanding is that developing BLE custom GATT profiles is similar to SPP but the difference is that BLE is extremely...
Hi,
I just started developing with nRF51DK, tested some working examples to figure the basic things out (Blinky, UART, etc).
I can't figure out how to make the multilink...
Hello,
I ordered some modules and expected them to be based on revision 2 nRF51822.. But they use Revision 1. Now I am struggling getting my Code from the nRF51-DK to work...
Hi
I am writing an application that requires bonding/paring stuffs and face a problem as below
The maximum bonds that my device can manage is 2. When these 2 slots are...
Hi
I use nRF6310 and PCA10005 to develop BLE project. When entering DTM tab, I cannot find the motherboard on "set up on".
DTM.jpg
My hardware is:
motherboard: nRF6310...
Dear Support,
we have done some technical question
About the N5 module of Dynastream (with nRF51422) we would like to program the software placed into the application...
my android program add many nRF51822 devices mac adress to a file in my android device.So I can count number of connected nRF51822 to my android device with bluetooth low...
Hi,all.i want to integrate ble_dtm(6310 board) to ble_proximity(pca1001 board).Can someone give me advise? i run ble_dtm on my board,and cannot find "Nordic_DTM" when i scan...
Hi,all.i want to construct our product test system.i follow AN34 page6 (figure 2) to do this.i have a question: DUT and nRF DK module run same firmware ? if correct,when nRF...
Hi,
In my application, I would like to take some action, when the bonding is removed from the phone.
At the moment I'm using static key for bonding and I see that BLE_GAP_EVT_SEC_PARAMS_REQUEST...
I'm using SDK 7.1, SD310 2.0.1, MCP 3.8.0.7
I have two versions of a board with the nRF51. Some of them have the 32kHz crystal and some don't. In my application I have...
