Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello,
I am trying a IOT SDK example to connect a NRF52840 to a Raspberry Pi 3 via ipv6:
infocenter.nordicsemi.com/index.jsp
I don't use a low energy dongle because...
I've worked on nRF DFU Library on Android where you can easily do OTA DFU. Same with the nRF Connect desktop application. I was wondering if anyone knows any library (preferably...
I'm developing a BLE gateway/scanner for nRF5 Mesh BLE network, my system components are as following:
Raspberry Pi 3 installed with noble nodejs library (as I'm...
Hello,
I am using nRF52832 s132 soft device and i have read accelerometer adc 3 axis value with sample rate of 244us instead of ms. For controlling my device i have send...
log1.pcap Hi, I am developing a peripheral application that can send around 68k of data in the notifications to the central
Notifications are send at the frequency of 284...
I took the ble_app_hrs code and made changes to suit my application (increased number of peripherals, included bonding/pairing, included ble_nus, added code for button, led...
We have problems when connecting to a device running softdevice S132 version 3.0 with a tablet running Android 7.0.
When we use tablet and nRF Connect, we get Error 8 ...
I tried to add ble_nus service to buttonless app (sdk 14).
Keil doen't raise any errors and compiled project, but app is not work actuall in NRF_LOG I can see these messages...
Hello,
I'm confused regarding the nRF82840 matching network found in the datasheet and dev kit. Is the Pi-filter composed of C3-L1-C4 the 50ohm matching network or should...
Hi,
I have a Rigado BDM-300 (nRF52832) on a small custom board.
Using SDK 13.1 with SD132 v4.0.2.
I've taken a template project and adjusted it to my needs. I can get...
Not sure if there is already a worked-out example of converting analog to digital data from AIN0 and then updating a characteristic with that data.
I've worked through...
Hello ,
I am using examples\ble_central\ble_app_uart_c\pca10031\s120 in the SDK 10.00 .
I know that s120 supports up to 8 peripherals. I am using NRF51 Dongle as a Central...
hello everyone:
i use nrf51822QFAC(with 256kb flash and 32kb ram).The project is this "SDK12.3-ANCS\examples\ble_peripheral\ble_app_ancs_c\pca10028\s130\arm5_no_packs"...
