I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi,
I have Nordic NRF52 DK. What chip does it have? because there are quite many chips of NRF52 series and can you also tell me about the PCB reference design of the chip...
According to the PDM of the nRF52810 datasheet，the input of the filter is the two-channel PDM serial stream (with left channel on clock high, right channel on clock low),...
I am looking at a Bosch GLM50C and when i connect with nrf connect on IOS I can only see device information and a custom service, on android I can also see the generic access...
Hi,
I want to confirm two points in the PCB layout of nRF52:
In the data sheet and in the reference circuits section, there are no caps on pins 37 and 38 (QFN...
I made up a prototype board with BLE Nano2, connected via a JLink.
I'm using armgcc. JLink is needed to support RTT as I need the UART for another purpose.
My board file...
I'm upgrading an SDK13.1.0 project to SDK14.0.0. I'm using bonding and Peer Manager. nRF52832. Softdevice S132 5.0.0.
I no longer get any PM_EVT_PEER_DATA_UPDATE_SUCCEEDED...
Hello,
I am using nRF52832 DK, and implement my software using eclipse with ARM GCC complier sdk12.1. I have interface accelerometer sensor with this board. I have read SAADC...
Hello,
I have a brief question regarding to SPI, I have two instances of SPI, SPI0 and SPI1, I was wondering whether or not changing the value of SPIS_CSN_PIN to SPI0 would...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hello,
I am using the Nordic NRF 51822 chip and are am wondering if full Eddystone support can be found in the latest firmware? I have read on github ( github.com/.../nrf5...
Hi,i m working in uav project with nr52 and GY-87 that contains mpu6050 and hmc8553 as sensor. i use i2clib to do connexion with twi created by jeff rowberg, then i wrote...
Hi,
I'm trying to add Openthread support to my project, which is based on ATT_MTU_Throughput example. I followed the tutorial in infocenter, but I still have some problems...
Hi,
I am attempting to run the various USB example programs on the nRF52840-PDK USB, but my nRF usb device is not being recognized (in windows OR linux device tree). Is...
Hi.
I just spend 2 days debugging problem with dfu. In the function nrf_dfu_app_continue the function nrf_dfu_flash_store is called with len parmeter as bytes and should...
