Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
I just spent 2 hours chasing BLE bug after upgrading from s132 v3 => v4.0.2
I added a call
// Configure the maximum ATT MTU.
memset(&ble_cfg, 0x00, sizeof(ble_cfg)...
I couldn't use nRF Connect (BLE) under Linux, after updating the FW, it tries to open /dev/ttyACM0 but fails to do so.
Not a "permission" problem: the user is in uucp...
Hi,
I'm unable to compile the OpenMesh example application. I've modified the make file with correct paths. However I'm getting the following error. Can you please help...
I have a NRF51 talking through the UART to another uC, and I'm trying to log messages through Segger RTT. Everything works normally until I start to send some data through...
If SEGGER_RTT_CONFIG_DEFAULT_MODE is "BLOCK", the program won't start without RTT attached - at least for me... is there a possible solution?
I mean, technically it makes...
hello ,everyone
I was confused by a PWM problem for a long time , on nrf52832 SDK13 ,i wanna change the PWM duty cycle every period ,but now i find can not change it at...
Hey dear Devzone,
I am trying out some Thread and BLE dynamical examples on my nRF52840's but running into some problems using the " ble_thread_dyn_mtd_coap_cli " example...
Hello nordic dev community,
I am completely new to nordic products. I attended one of the conference and got more information regarding developer zone and info center....
Hi,
I am wondering why the ccm library uses the software aes encryption. Is there anything wrong with the hardware encryption so that it should not be used?
Marius
Hi there,
hope you are doing fine.
I am using SDK 14.1 with SoftDevice 132 as well as a state machine framework which needs a have a function called periodically to...
Hi. I'm using nRF52832, SDK13.0.0 as peripheral.
When I want to disconnect central, I'm using sd_ble_gap_disconnect function as below.
err_code = sd_ble_gap_disconnect...
When I try to build and run any example from the nRF5 SDK, it can compile successfully. But when loading to the eval kit, it can't find the 's140_nrf52840_5.0.0-2_alpha_softdevice...
Hello Everyone,
I am using nrf51822 256Kb Flash and 32KB RAM Raytac's BLE module with SDK11, S130 with over the air Bootloader (16Kb).
So the aim is that when a particular...
Hi all,
I encountered a problem , when I connect 1 board central to 2 board peripheral via NUS . It connected and discovery success . But at
static void db_disc_handler...
