Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello,
I work on an application which use the pc-ble-driver 1.0 as BLE central for handling external peripheral devices.
Now, I am working on bonding procedure. To make...
I'm attempting to take a 115k baud stream of NMEA sentences from a GPS sensor, and outputting it to a phone based on the UART example. While I'm not sure if BLE is perfectly...
Using the ble_app_uart example on the nRF52 PDK, I can easily send multiple packets per connection interval--if I send a long string using ble_nus_string_send(), the notification...
Hi.
I've just received my nRF52840-PDK and now I am trying to run usb examples from SDK 13.1.0.
I have started with VisualGDB using arm-eabi toolchain and USB HID Generic...
Setting interrupt priority according to FreeRTOS documentation is an inverted priority sequencing, i.e. lower number is high priority. However in the freeRTOS example provided...
Hi,
I am seeing an issue where after enabling read back protection (rbp) on NRF52 and using sdk 12.1 the tag goes to state where it drains a lot of current.
command used...
Hello!
I'm using SDK 12.3.0 with nRF51822. Unfortunately since the begining I've got a problem with TWI interface. It keeps crushing my app. For no reason. At the beginning...
Hello,
I am using sdk 12.3.0 and pca10040 board. I want to update the firmware OTA. I am following this post
devzone.nordicsemi.com/.../
I am stuck at step 4)...
I am using the nRF52832 development board, S132 and SDK11.0, I have some questions about Bluetooth pairing,The project under the link：examples\ble_peripheral\ble_app_uart...
when we use twi to transmit data in iic mode ,the nrf52832's power is unacceptable,too high!we read and write data in 50times per second.every time, we transmit 24 byte data...
I JUST NEED TO KNOW NUMBER OF ON PULSES PRESENT IN THE PWM OUTPUT CAN I USE PIN CHANGE INTERRUPT TO COUNT THE NUMBER OF ON PULSES OR SOME OTHER METHOD IS AVAILABLE
Hi,
We need to pass the radio certification and in order to simplify the setup we created an application to setup BLE TX/RX/CC/MC from an NFC command but we meet a strange...
Hello,
As a lot of person, I have a problem for use nrf52832(pca10040 board) with spi as slave.
I check my master with salae probe tool and this part is correct. Chip...
Hello,
my nRF52 Preview dev.kit don't upload the last 2016 march 15 firmware update
from nRFgo app. It gives me always an error and the progress bar stay at 0% value.
...
