[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
Can I use J-Link EDU for nRF52840-PDK , nRF Connect , please?
Is it sufficient?
What the J-Link PRO provides for nRF52840-PDK, nRF Connect that the J-Link EDU does not?
Question preamble
I am writing a bluetooth application where two nRF5 devices will be in a master / slave configuration. However, I want to be able to flick a physical...
Hi.
I have an application that needs a low security encryption. Therefore I want to use "Just works" encryption. The pairing process is assumed to be in a "safe" place...
I am having a strange problem. After I flash the program to the NRF52 and do a reset (does not matter whether it is a soft reset or pin reset) the system (DK and my own board...
Hi,
i read this post:
devzone.nordicsemi.com/.../
and found the PCA20006 project but i cannot load it to the beacon. I can find proper instructions on how to load...
I had initially added ble_dfu buttonless DFU support (unbonded) to my app per instructions here: infocenter.nordicsemi.com/.../service_dfu.html
Long story short, based...
What unique information can I use to know which physical device disconnected for example? Say I have a MAC address or a name encoded into the advertising packet. Correct me...
Here the connect method is called
err_code =
sd_ble_gap_connect(
peer_addr,
&m_scan_params,
&m_connection_param,
APP_BLE_CONN_CFG_TAG);
In the ble event...
I'm tring to connect my phone to the multi-connect example client app
I'm tracing the ble events in the ble_evt_handler.
When I open the server app on my phone, I see...
Hi Engineers!
faced with a problem of SAADC impedance too small (4,7K)!
We use SINGLE ENDING 8bit mode with following settings:
NRF_SAADC_REFERENCE_VDD4
NRF_SAADC_GAIN1_4...
We are moving from a PCB using a nRF51822 QFAB module to a newer PCB using an nRF51822 QFAC module.
We observed that with the new QFAC PCB we have a significant connection...
I want to use the nrf52dk PCA10040 to remote program a BC832 chip from Fastel.
They say:
"BC832 V1 pin B3 C3 (DCC, DEC4) needs to be connected to the program can be burned...
I have an nrf52832 BLE HIDS device based, with the connection and peer handling code copied from the hids keyboard example, SDK13. I use Windows 10 as host. Setting up a connection...
I plan to keep the bonded device information in the ring buffer, but there are a few things that puzzled me:
When PM_EVT_CONN_SEC_CONFIG_REQ event is received, .allow_repairing...
