I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
An unprovisioned device will advertise a beacon and the spec says that it shall be advertised with non-connectable and non-scannable undirected advertising events
...
Hello there,
for a project I would like to use the Arduino Primo core with the nRF52832 chip to read a NFC Tag.
I could not figure why it can´t read a tag even though...
Hi,
I've test the light_control example with the PCA10028 & PCA10040 recently. The PCA10040 was test and it works normally, but the PCA10028 does not.
I have also checked...
I am working on an application that allocate data dynamically at initialization, and my malloc/calloc returns NULL a lot earlier than I expected.
Using a debug macro, I...
Use the E: \ Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart \ pca10040 this routine
Run to chart a breakpoint on the resumption of here
...
Hi guys,
I'm trying to use the HFCLK to generate high resolution timing. Ideally at the millisecond resolution. I've written a layer around the nrf_drv_timer.c module....
Hi,
I followed the tutorials you made to start developing BLE applications for nRF52 series development board. Then I started to make my custom application (in fact, it...
Hi everyone,
I have been reading the Specifications of Bluetooth 4.1, mostly about Universally Unique Identifiers (UUIDs) for Services, Characteristics, etc.
I found...
Respected sir,
setup for programming = Eclipse-gcc-toolchain-setup
board = PCA10040
as per my way first take a ble_app_uart code startup my coading purpose.
then we...
Hi Guys,
I'm doing the following before putting my device to sleep. This works fine when I use NRF_POWER->SYSTEMOFF, but when I use sd_power_system_off(), it doesn't seem...
Hello,
I am using nRF52832 development kit. I used different examples to send data. But i couldn't accomplish to send data packet over 20 byte. The max data size is defined...
I'm planning to use nRF51422 QFAAE00 as ble central. I try to compile the SDKv10.0.0\examples\ble_central\ble_app_hrs_c and SD130. And another one as ble peripheral using...
Anyone had a successful attempt at using the fds(flash data storage) module( http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v11.0.0%2Flib_fds...
Hello,
Today I stumbled upon very strange nRF52832 behaviour which I cannot explain. I am using two TWIM instances (0 and 1) and one SPIM instance (2).
First strange...
