Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I'm using nrf51822 and ble_app_uart(SDK 12.3.0).
I'm sending data from my android phone.
My question is that what happen if send data before previous data is...
Hi!
I am developing application for thread on NRF52840. I've got one problem with connection stability. Sometimes some SED nodes are disappearing. Only reset makes them to...
I am using CC2541 and CC2540 (USB dongle) which will communicate with each other and transfers data. I want to know weather i can communicate to CC2541 (ble device) directly...
Hello,
We have a setup where we connect an nrf51822 and an iphone.The nrf51822 connects to the iphone,
notifies the data and disconnects roughly every minute.(This is done...
There are only HID periphral sample code in nRF52840 SDK.
It is difficult for me to implement HID central with the sample and tutorial provided.
So I want to get a sample...
Capture_Load_error.PNG
All,
I'm new to the nodic. Just now installed KEIL V5.24.2.0.'m able to compile code but not able to load it on Target.
Please find attachment...
Hello,
It doesn't seem possible to mimic a IEEE public BLE MAC address using the BLE stack provided by Noridc. But how easy is it for others to roll their own BLE stack that...
For longer than I'd like to admit, I've been trying to make an application on the NRF52832 that relays UART data to a phone. To date, I've:
Gotten the BLE_APP_UART application...
hello all：
I think sdk13.1 s132 has a bug about ANCS，
ANCS works normally only in the following two cases
1、Both the phone side and the device side do not remember...
I have a sensor with serial protocol of 7 bits data, even parity, 2 stop bits. I wanted to use uart library to interface with this sensor. But I couldn't find the settings...
Some times when I'm trying to use GDB it stop with the following information:
(gdb) file _build/nrf51822_xxab.out
A program is being debugged already.
Are you sure you...
I started to try SAADC example in SDK12.3. After setting up project in eclipse, I got two errors:
Symbol "NRF_TIMER0" could not be resolved
Symbol "TIMER0_CC_NUM" could...
Hi,
We are a group of students at NTNU looking at the possibility of creating a small device that connects to your phone and multiple other BT devices simultaneously, letting...
Hello,
This is a quick question regarding the behavior of the Power Supervisor POF warning. We implemented a fairly naive use of the POF warning where we would log an POF...
Hello I am using the NRF52832 in ESB mode. I use both VERIFY_SUCCESS() and APP_ERROR_CHECK() within my code in various places but when am I supposed to use versus the other...
